![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
wc piston in 226 |
Post Reply ![]() |
Author | |
woody4178 ![]() Bronze Level ![]() Joined: 18 Dec 2013 Location: kansas Points: 22 |
![]() ![]() ![]() ![]() ![]() Posted: 28 Dec 2013 at 6:58pm |
I have a 226 4 1/8 bore 4.5 stroke out of a wd45 am wanting to put wc pistons in it I am tryin to avoid stroking it. Question is will this work,what are the wc pistons compression height and what kind of compressiom ratio/hp will I be getting. Fairly new to all this looking for advice.thanks
|
|
![]() |
|
Sponsored Links | |
![]() |
|
Kip-Utah ![]() Orange Level ![]() ![]() Joined: 14 Sep 2009 Location: Southern Utah Points: 874 |
![]() ![]() ![]() ![]() ![]() |
Yes you can run flat top WC or WD 4.125" replacement pistons with your combination. I'm running a similar combination but elected to go with 4.125" 170/175 crater pistons. We also used a WD45 block. This combo works out to be right at 240 cid and around 8.25:1 compression, and is good for about 58 hp at 2000 rpm. Depending which flat top pistons you use your compression ratio should be a little higher than ours. Kip
![]() Edited by Kip-Utah - 30 Dec 2013 at 1:27pm |
|
HANSEN'S OLD ORANGE IRON. Showing, Pulling, & Going!!
|
|
![]() |
|
woody4178 ![]() Bronze Level ![]() Joined: 18 Dec 2013 Location: kansas Points: 22 |
![]() ![]() ![]() ![]() ![]() |
Thanks kip pretty sure we are guna run wc flat tops 4.125 and s 170 cam
|
|
![]() |
|
BennyLumpkin ![]() Orange Level ![]() ![]() Joined: 22 Mar 2010 Location: Centre Hall, PA Points: 2657 |
![]() ![]() ![]() ![]() ![]() |
Good luck finding a 170 cam....
|
|
Central PA Allis Express
1934 WC254 1945 WF 1945 WC135755 1951 WD68085 1953 WD45-150217 1957 WD45D-230744D B110 |
|
![]() |
|
woody4178 ![]() Bronze Level ![]() Joined: 18 Dec 2013 Location: kansas Points: 22 |
![]() ![]() ![]() ![]() ![]() |
I did get lucky on the cam father in law hss one already to go
|
|
![]() |
|
BennyLumpkin ![]() Orange Level ![]() ![]() Joined: 22 Mar 2010 Location: Centre Hall, PA Points: 2657 |
![]() ![]() ![]() ![]() ![]() |
Very lucky
|
|
Central PA Allis Express
1934 WC254 1945 WF 1945 WC135755 1951 WD68085 1953 WD45-150217 1957 WD45D-230744D B110 |
|
![]() |
|
Bill_MN ![]() Orange Level ![]() ![]() Joined: 12 Sep 2009 Location: Sioux Falls, SD Points: 1466 |
![]() ![]() ![]() ![]() ![]() |
isn't it the 175 gas cam that's hard to find? or are they the same?
|
|
1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow
|
|
![]() |
|
DrAllis ![]() Orange Level Access ![]() Joined: 12 Sep 2009 Points: 21021 |
![]() ![]() ![]() ![]() ![]() |
A 170 cam isn't any different grind than a D-17 or "E" Gleaner or WD45 or WC for that matter. The "175" camshaft is the special high lift grind.
|
|
![]() |
|
dawntreader74 ![]() Orange Level ![]() ![]() Joined: 28 Oct 2013 Location: Manteno Points: 1770 |
![]() ![]() ![]() ![]() ![]() |
SR' find you some small block chevy pistons with same rist pin holes. works fine.
|
|
![]() |
|
bmartin55 ![]() Silver Level ![]() ![]() Joined: 20 Feb 2013 Location: OH Points: 97 |
![]() ![]() ![]() ![]() ![]() |
hi want to do same thing ..i have a 17 gleaner motor..need 4.125 pistons.want to grind crank& use 350 rods..OR 350 sbc pistons.. bob
|
|
![]() |
|
Glockhead SWMI ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: South West Mich Points: 2657 |
![]() ![]() ![]() ![]() ![]() |
SBC 350 rods?
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |