| Author |
 Topic Search  Topic Options
|
MyHd6G 
Bronze Level
Joined: 09 Jun 2023
Location: Pittsburgh
Points: 6
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: HD6G pinion shaft
Posted: 09 Jun 2023 at 8:45pm |
|
Hi All,
I have aliis chalmers HD6G high lift I pulled the steering clutch and pulled the pinion shaft out and found the pinion gear is shot, was wondering if your able to pull the pinion gear out with out taking out the intermediate shaft and final drive gear out? Thank you
|
 |
|
Sponsored Links
|
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41608
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Jun 2023 at 11:35pm |
|
Pinion shaft would be part of the transmission that indexes into ring gear , and ring gear is flange mount to the brake/clutch drum .
Which section are you in the final drive and 3 reduction gears in the outer housing ?
If so believe the only way it to drop all the gears out which means pulling the axle also
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
MyHd6G
Bronze Level
Joined: 09 Jun 2023
Location: Pittsburgh
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Jun 2023 at 6:42am |
|
It is the very top gear that has the shaft coming off the steering clutch, I got that shaft out and the gear drops down in, I can reach up from the bottom and grab it and will come down some but it doesn’t seem it has enough room to come out.
|
|
gemdozer
Orange Level
Joined: 17 Sep 2009
Points: 989
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Jun 2023 at 7:57am |
|
Did you try to turning the bulgear front in back maybe the pinion could go down or if you removed the top shaft cage and try to fisch the pinion and the pinion is 5 1/2 inch hight
|
|
MyHd6G
Bronze Level
Joined: 09 Jun 2023
Location: Pittsburgh
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Jun 2023 at 8:25pm |
|
Tried to get the gear over the bull gear it is just barely to big but it is not able to clear the housing, also the bearings measures 5”, wasn’t able to get it through the housing.
|
|
Codger
Orange Level
Joined: 23 Dec 2020
Location: Utopia
Points: 2041
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Jun 2023 at 8:36pm |
 MyHd6G wrote:
It is the very top gear that has the shaft coming off the steering clutch, I got that shaft out and the gear drops down in, I can reach up from the bottom and grab it and will come down some but it doesn’t seem it has enough room to come out. |
This help?
|
|
That's All Folks!
|
|
doctorcorey
Orange Level
Joined: 17 Jul 2011
Location: S. KC Missouri
Points: 589
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Jun 2023 at 8:37pm |
|
I would suggest you pull the bottom cover from the final case and closely check the intermediate shaft for looseness. These bearings are much more prone to failure. There should be NO endplay or radial movement in this shaft.
|
|
Semper Fi USMC 1958 HD6G, 1959 MF 203 loader, 1960 Case 420B Backhoe, MF 65 Tractor/Loader Diesel
|
|
MyHd6G
Bronze Level
Joined: 09 Jun 2023
Location: Pittsburgh
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Jun 2023 at 8:41pm |
|
The intermediate shaft is the shaft in between the final drive pinion shaft and the shaft that has the bull gear on it?
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81309
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Jun 2023 at 9:18pm |
|
|
|
Like them all, but love the "B"s.
|
|
MyHd6G
Bronze Level
Joined: 09 Jun 2023
Location: Pittsburgh
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Jun 2023 at 9:12am |
|
The intermediate shaft I did check it does not have slop in it, but I am still having problems getting the pinion gear out. I was reading in the book they said they slip the pinion gear in then put the intermediate shaft and the bull gear in, would that be the only way to get the pinion gear out?
|
|
