Pulling with a B110

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I am about to start the process of turning a B110 into a stock/stock altered puller.  It has the three speed in it.  I have a 16HP cast iron Briggs to go in it too.  I was wondering what tricks I need to do to the transaxle to beef it up.  Should I install a bevel gear box off of a 700/900 series?  They are a bit heavier from what I understand.  Thanks.

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
KevinON Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 07 Dec 2009 Location: Schomberg, ON Points: 786	Post Options Post Reply Quote KevinON Report Post Thanks(0) Quote Reply Topic: Pulling with a B110 Posted: 09 Mar 2015 at 12:42pm
	I am about to start the process of turning a B110 into a stock/stock altered puller. It has the three speed in it. I have a 16HP cast iron Briggs to go in it too. I was wondering what tricks I need to do to the transaxle to beef it up. Should I install a bevel gear box off of a 700/900 series? They are a bit heavier from what I understand. Thanks.

Sponsored Links

tbran Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 14 Sep 2009 Location: Paris Tn Points: 3244	Post Options Post Reply Quote tbran Report Post Thanks(0) Quote Reply Posted: 09 Mar 2015 at 2:11pm
	if rules allow, do the component thing with a cadet type rear. Look on line hundreds of options. The differential is the weak point on the simplicity/allis when used for pulling, then the bevel gears, I don't know if the 900 are heavier or not, but they are not heavy enough for serious pulling... this has been our experience,
	When told "it's not the money,it's the principle", remember, it's always the money..

edard12 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 18 Feb 2015 Location: Mt. Pleasant, P Points: 7	Post Options Post Reply Quote edard12 Report Post Thanks(0) Quote Reply Posted: 11 Mar 2015 at 11:57pm
	We've been pulling B series AC's since the late 80"s. The two weak spots in the rear are the axle tube and the right side hub that goes into the differential. The hub fix is get one out of a 700 or 900 series. The axle tube fix is a solid axle and billet hubs. If your running 23 x 10.50 tires a solid axle isn't needed. Been running a B-10 with without a solid axle for 20+ years on same axle tube. If rules allow make the rear a positive traction it will save axle tubes and make it pull better. Have a 710 with a K361 single ohv Kohler on alcohol making about 70hp. I know the weak spots. If your staying stock or stock altered you don't need the cub stuff.

KevinON Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 07 Dec 2009 Location: Schomberg, ON Points: 786	Post Options Post Reply Quote KevinON Report Post Thanks(0) Quote Reply Posted: 12 Mar 2015 at 11:52am
	That sounds like what I will need to do. I want to keep it as original as possible. It may not be a winner, but everyone else runs cubs, so it is nice to be different. I have sent you a PM, edard12.