This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


2000 Plow
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
DOlson View Drop Down
Silver Level
Silver Level
Avatar

Joined: 25 Dec 2009
Location: Sarona WI
Points: 57 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DOlson Quote  Post ReplyReply Direct Link To This Post Topic: 2000 Plow
    Posted: 22 Apr 2011 at 11:42pm
How bad of a job is it to replace the pivot pin bushings on the re-set stub beam on a hydraulic re-set plow and how much play is excitable?

Thank Derrick   
Back to Top
Sponsored Links


Back to Top
Jim Hancock View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: EL Reno, Ok.
Points: 1112 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jim Hancock Quote  Post ReplyReply Direct Link To This Post Posted: 22 Apr 2011 at 11:48pm
Don't know. We never did that I remember. Maybe we just didn't need to, otherwise I would've been in the middle of it helping dad.
Back to Top
JimWenigOH View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: NC Ohio
Points: 1198 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JimWenigOH Quote  Post ReplyReply Direct Link To This Post Posted: 23 Apr 2011 at 6:28am
I needed some parts from one from a salvage yard one time. After beating on it with a big hammer for a while, the fellow gave up and I bought the complete assembly to keep the part I needed from getting damaged. I have a press I plan to use when I get around to it. In the mean time I occasionally squirt penetrating oil on the joints to soften things up.
Back to Top
427435 View Drop Down
Orange Level
Orange Level


Joined: 18 Nov 2010
Location: SE Minnesota
Points: 18637 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 427435 Quote  Post ReplyReply Direct Link To This Post Posted: 23 Apr 2011 at 10:15am
You will need a big wrench to get the nuts loose and properly tight again.  I remember buying a 600 ft-lb torque wrench (but not the actual torque setting) when I was testing these trips.
Mark

B10 Allis, 917 Allis, 7116 Simplicity, 7790 Simplicity Diesel,
GTH-L Simplicity

Ignorance is curable-----stupidity is not.
Back to Top
DOlson View Drop Down
Silver Level
Silver Level
Avatar

Joined: 25 Dec 2009
Location: Sarona WI
Points: 57 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DOlson Quote  Post ReplyReply Direct Link To This Post Posted: 23 Apr 2011 at 6:59pm
I have the tools just need to know is more work than its worth, plow has a lot of good parts. Or should I just use it tell its wore out 
Back to Top
DOlson View Drop Down
Silver Level
Silver Level
Avatar

Joined: 25 Dec 2009
Location: Sarona WI
Points: 57 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DOlson Quote  Post ReplyReply Direct Link To This Post Posted: 24 Apr 2011 at 9:35pm
bump
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.061 seconds.


Help Support the
Unofficial Allis Forum