| Author |
 Topic Search  Topic Options
|
Kevin210 
Silver Level
Joined: 08 Oct 2018
Location: Indiana
Points: 428
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Decals
Posted: 02 Jun 2023 at 3:18pm |
|
Has anyone used decals from DJS,if so what did you use
to put them on with as far as soapy water or something else.
|
 |
|
Sponsored Links
|
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5232
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2023 at 8:17pm |
|
I would contact them, I only use water and a little Dawn detergent but I buy mine from a different company. Depends if it’s Mylar or vinyl?
Edited by AC720Man - 02 Jun 2023 at 8:20pm
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 968
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2023 at 10:41pm |
|
Maple hunter decal is where I got my vinyl decals for my wd…
I cleaned where I was going to put them on and put them on dry…
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
JimD
Orange Level
Joined: 11 Sep 2009
Location: Mounds, OK
Points: 2116
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2023 at 5:34pm |
|
Call dj's?
|
Owner of OKtractor.com PM for an instant response on parts. Open M-F 9-6 Central. We have new and used parts. 877-378-6543
|
|
Codger
Orange Level
Joined: 23 Dec 2020
Location: Utopia
Points: 2458
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2023 at 5:51pm |
Isopropyl alcohol in a spray bottle will help you both find open sores, and slide the decals into position to squeegee out. Use a medium hard rubber squeegee for the purpose with very clean hands.
|
|
That's All Folks!
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5232
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2023 at 9:39pm |
|
Water/Dawn detergent solution allows me to move the decal in place in case I’m off. Blot dry and squeegee from the center out. Use only a few drops of Dawn with the water in a spray bottle.
Edited by AC720Man - 03 Jun 2023 at 9:39pm
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Calvin Schmidt
Orange Level
Joined: 11 Sep 2009
Location: Ontario Can.
Points: 4542
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Jun 2023 at 7:45am |
|
I got decals from DJS for my 220fwd and found the hood decal to be 3" shorter than my original 220. I don't know who's decals they sell. Have not bought directly from Maple Hunter. OneNinety decals from DJS for my early Series I have the same font as the later versions. Looking for correct series I decals. Wacker never responds .
|
|
Nothing is impossible if it is properly financed
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5232
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Jun 2023 at 1:30pm |
|
Go on Maple Hunter decals of Indiana website, all decals are listed. They have great decals for each series when changes were made.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21899
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Jun 2023 at 4:09pm |
|
Have always had good luck with Maple Hunter until the last time. I ordered new hood decals for my One-Seventy gas tractor. Good thing I checked everything before installation was underway, as each side was 3 inches too LONG !! Fairly east fix, but sure glad I didn't have the backside peeled off and then found out.
|
|
Kevin210
Silver Level
Joined: 08 Oct 2018
Location: Indiana
Points: 428
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Jun 2023 at 8:14pm |
|
Thanks guys.
I got some of the decals on this weekend
but still waiting to get the hood back from
being painted..
|
|
