Decals
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=195504
Printed Date: 08 Sep 2025 at 1:21pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Decals
Posted By: Kevin210
Subject: Decals
Date Posted: 02 Jun 2023 at 3:18pm
Has anyone used decals from DJS,if so what did you use
to put them on with as far as soapy water or something else.
|
Replies:
Posted By: AC720Man
Date Posted: 02 Jun 2023 at 8:17pm
I would contact them, I only use water and a little Dawn detergent but I buy mine from a different company. Depends if it’s Mylar or vinyl?
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: 55allis
Date Posted: 02 Jun 2023 at 10:41pm
Maple hunter decal is where I got my vinyl decals for my wd…
I cleaned where I was going to put them on and put them on dry…
-------------
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
Posted By: JimD
Date Posted: 03 Jun 2023 at 5:34pm
Call dj's?
-------------
Owner of http://www.OKtractor.com" rel="nofollow - OKtractor.com PM for an instant response on parts. Open M-F 9-6 Central.
We have new and used parts. 877-378-6543
|
Posted By: Codger
Date Posted: 03 Jun 2023 at 5:51pm
|
Isopropyl alcohol in a spray bottle will help you both find open sores, and slide the decals into position to squeegee out. Use a medium hard rubber squeegee for the purpose with very clean hands.
-------------
That's All Folks!
|
Posted By: AC720Man
Date Posted: 03 Jun 2023 at 9:39pm
Water/Dawn detergent solution allows me to move the decal in place in case I’m off. Blot dry and squeegee from the center out. Use only a few drops of Dawn with the water in a spray bottle.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: Calvin Schmidt
Date Posted: 04 Jun 2023 at 7:45am
I got decals from DJS for my 220fwd and found the hood decal to be 3" shorter than my original 220. I don't know who's decals they sell. Have not bought directly from Maple Hunter. OneNinety decals from DJS for my early Series I have the same font as the later versions. Looking for correct series I decals. Wacker never responds .
-------------
Nothing is impossible if it is properly financed
|
Posted By: AC720Man
Date Posted: 04 Jun 2023 at 1:30pm
Go on Maple Hunter decals of Indiana website, all decals are listed. They have great decals for each series when changes were made.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: DrAllis
Date Posted: 04 Jun 2023 at 4:09pm
|
Have always had good luck with Maple Hunter until the last time. I ordered new hood decals for my One-Seventy gas tractor. Good thing I checked everything before installation was underway, as each side was 3 inches too LONG !! Fairly east fix, but sure glad I didn't have the backside peeled off and then found out.
|
Posted By: Kevin210
Date Posted: 04 Jun 2023 at 8:14pm
Thanks guys.
I got some of the decals on this weekend
but still waiting to get the hood back from
being painted..
|
|