| Author |
 Topic Search  Topic Options
|
thester 
Bronze Level
Joined: 31 Jul 2022
Location: Marietta MS
Points: 15
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: ISO Power Steering Line for D17 series IV
Posted: 11 Aug 2022 at 7:32pm |
|
Looking for power steering line for D17 Series IV. If sitting on tractor it is the small line on the left side. Runs from pump to left side of reservoir on from of tractor.
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21384
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Aug 2022 at 9:28pm |
|
I'm going to assume a gas tractor ?? Diesel lines are all different. Lines from a series 3 are the same as a series 4.
|
|
thester
Bronze Level
Joined: 31 Jul 2022
Location: Marietta MS
Points: 15
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Aug 2022 at 5:49am |
Yes Sir. You are correct and thank you for the response. If I were to try and build a line myself. Would you know the size of the line # 5 and fittings? 
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21384
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Aug 2022 at 6:33am |
|
That's the pressure line, so it must be good enough for 1600 psi. If you don't have your old one for a pattern, that will be a challenge to make one identical. The pump hole is "inverted flare" which is kind of odd. The bottom is too, but you could make it into JIC connections.
|
|
thester
Bronze Level
Joined: 31 Jul 2022
Location: Marietta MS
Points: 15
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Aug 2022 at 7:18am |
|
I have the old one for a pattern and I should be able to reuse the fittings. I’m just unsure the exact size of the steel line. Once I have formed the line I should be able to have a high pressure hose attached.
|
|
Albert
Silver Level
Joined: 11 Sep 2009
Location: NW MO
Points: 410
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Aug 2022 at 7:53pm |
I am sure it is a 5/8 line but you better measure it. A 5/8 open end quality wrench will tell you. Albert
|
|
PaulB
Orange Level
Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4930
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Aug 2022 at 6:27am |
|
If you have the line; Send it to Inline Tube to have a replacement one copied from it.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
|
|
VaAllis1990
Bronze Level
Joined: 26 Jan 2022
Location: Champlain Va
Points: 23
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Aug 2022 at 7:20pm |
|
Agco still sells it
|
|
Albert
Silver Level
Joined: 11 Sep 2009
Location: NW MO
Points: 410
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Aug 2022 at 7:35pm |
|
70237389 NLA from AGCO
|
|
DSeries4
Orange Level
Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7434
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Aug 2022 at 5:12pm |
|
If you have the old one, a local hydraulic shop can make one to match it.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
thester
Bronze Level
Joined: 31 Jul 2022
Location: Marietta MS
Points: 15
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Sep 2022 at 6:51am |
|
Thanks for all the responses. Found the line from a gentlemen in PA via EBay.
|
|
