This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


d 17 missing and rough running
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
elalr View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 15 Sep 2010
Location: warsaw mo.
Points: 31 		Post Options Post Options   Thanks (0) Thanks(0)   Quote elalr Quote  Post ReplyReply Direct Link To This Post Topic: d 17 missing and rough running
    Posted: 26 May 2011 at 2:17pm
i have a diesel d17 thats running rough after i tried a repair. my injecter pump is leaking around the shaft on the side so i pulled the center bolt out of the arm for the throttle and pried it loose. im not so sure that is how it was supposed to come apart. i saw a brass sleeve around the shaft and decided that it was probably worn. i then tried to put it back together. the shaft had a hex head and i thought i carefully placed it back in the same place. once together i started it and it ran terrible. unfortunately i did not start it right before. i looked it over and took it back apart tried once again to line it up but it ran the same. could i have gotten air in the systen from the leaking shaft. i need this running badly! i just had a new baby and i need to sell it. someone please help me haha! thanks!
Back to Top
Sponsored Links


Back to Top
Brian Jasper co. Ia View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Prairie City Ia
Points: 10508 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Brian Jasper co. Ia Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2011 at 6:41pm
Hopefully Dr Allis, MACK, or InjpumpEd, will see this. Seems like some of the governor linkage is in the top that you took off. Last time I had one of those pumps apart was in trade school almost 25 years ago...
"Any man who thinks he can be happy and prosperous by letting the government take care of him better take a closer look at the American Indian." Henry Ford
Back to Top
Orange Blood View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Nov 2010
Location: ColoradoSprings
Points: 4053 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Orange Blood Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2011 at 8:13pm
I am not an IP expert by any means, but in looking at the exploded view of that pump, I don't think you can do what you did.  How much you asking for the 'ol girl, running, and current condition?
 
If you were really lucky you just have a pump full of air, I would crack the lines at the injectors while the engine is running until all the air is out for sure (no bubble, only strong stream), and find out.


Edited by Orange Blood - 26 May 2011 at 8:15pm
Still in use:
HD7 WC C CA WD 2-WD45 WD45LP WD45D D14 3-D17 D17LP 2-D19D D19LP 190XTD 190XTLP 720 D21 220 7020 7030 7040 7045 3-7060
Projects: 3-U UC 2-G 2-B 2-C CA 7-WC RC WDLP WF D14 D21 210 7045 N7
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2011 at 8:13am
To get that shaft out you need to remove the top then remove a clip that holds the two shafts togather which is the shutoff tab.
 Nothing in that area that would cause it to run rough but the top needs to be removed and propperly reassemly befor it is started again. If the clip came off when you pulled the shaft, it could get in a wrong place causing a runaway or in gov. weights causing alot of damage.
  If I was you I would get some one who knows these pumps to look at it befor it was started again.   MACK
Back to Top
mattb View Drop Down
Orange Level
Orange Level


Joined: 11 Jan 2011
Points: 348 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mattb Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2011 at 8:30am
The clip fell out of my injector pump and cracked the housing. Dont run it until u find that clip and put it back in.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.062 seconds.


Help Support the
Unofficial Allis Forum