This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Dual wheels for a wd45 ???
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
mark-east-tn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 06 Oct 2009
Location: Rutledge Tn
Points: 761 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mark-east-tn Quote  Post ReplyReply Direct Link To This Post Topic: Dual wheels for a wd45 ???
    Posted: 12 Nov 2010 at 9:48am
  Does anyone have a picture or the the stuff to add duals to a 45  they would sell.  I have one I would like to put duals on ,   thanks for help. 

Edited by mark-east-tn - 12 Nov 2010 at 9:48am
Back to Top
Sponsored Links


Back to Top
R Aiken View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: wc Ohio
Points: 1370 		Post Options Post Options   Thanks (0) Thanks(0)   Quote R Aiken Quote  Post ReplyReply Direct Link To This Post Posted: 12 Nov 2010 at 10:38am
I have 2 or 3 pair of them, I will see if I can find them. I will get you a pictuer later. Richard
Back to Top
Bret (OH) View Drop Down
Silver Level
Silver Level


Joined: 15 Sep 2009
Location: Blanchester, OH
Points: 347 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bret (OH) Quote  Post ReplyReply Direct Link To This Post Posted: 12 Nov 2010 at 11:08am
Best dual setup is to use another set of the stock wheel assemblies and turn them around backwards with the dish facing out, and bolt them on using a longer lug bolt right to the center hub.  Swap sides with the reversed wheels so the tread points the correct direction.  We ran one for a long time like that with all four tires loaded.  Looks good too.
Back to Top
Calvin Schmidt View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Ontario Can.
Points: 4526 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Calvin Schmidt Quote  Post ReplyReply Direct Link To This Post Posted: 12 Nov 2010 at 4:19pm
I run two Power shift wheels back to back for duals on my A-C 715B backhoe. The rims are from D-17IV and the tires are 16.9 x 28. I had to make an axle extention for the backhoe to get the correct offset so I made the hub wide enough for both rims to take the load off the studs. Use it with an 8' stone fork for picking stones on worked ground.
Nothing is impossible if it is properly financed
Back to Top
RichinWis View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Deforest Wis
Points: 691 		Post Options Post Options   Thanks (0) Thanks(0)   Quote RichinWis Quote  Post ReplyReply Direct Link To This Post Posted: 13 Nov 2010 at 10:17am
I have a couple pages from the Allis Chalmers serice manual detailing installation of these. I think it was for a D14 but would be the same idea on a 17. It is just like some of the posts are on here with the center hubs front to front with a spacer ring that sits in between the wheel flanges. I will see if I can find it and post it.
Back to Top
Ted J View Drop Down
Orange Level
Orange Level
Avatar

Joined: 05 Jul 2010
Location: La Crosse, WI
Points: 18869 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ted J Quote  Post ReplyReply Direct Link To This Post Posted: 14 Nov 2010 at 11:18am
I'd like to see pics of them too Richard. Can't wait to see them!! Thanks
"Allis-Express"
19?? WC / 1941 C / 1952 CA / 1956 WD45 / 1957 WD45 / 1958 D-17
Back to Top
Gary(VA) View Drop Down
Silver Level
Silver Level


Joined: 13 Sep 2009
Location: Troutville, VA
Points: 336 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary(VA) Quote  Post ReplyReply Direct Link To This Post Posted: 14 Nov 2010 at 11:58am
Mark, I sent you a PM, I'm in Roanoke, VA
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.074 seconds.


Help Support the
Unofficial Allis Forum