This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Cutting Tooth/Edge
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Boomer View Drop Down
Bronze Level
Bronze Level


Joined: 13 Sep 2009
Location: Mid Missouri
Points: 102 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Boomer Quote  Post ReplyReply Direct Link To This Post Topic: Cutting Tooth/Edge
    Posted: 07 Apr 2010 at 10:54am
Have a WC Speed Patrol, and the cutting tooth/edge for the blade is marginal. One side is worn more than the other by almost one and a half inch. Is there a place to get another set? From my measurements they appear to be the same as the Onyx snap coupler blades. Where does people get the replacements for the snap coupler blade?
Back to Top
Sponsored Links


Back to Top
CTuckerNWIL View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: NW Illinois
Points: 22823 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CTuckerNWIL Quote  Post ReplyReply Direct Link To This Post Posted: 07 Apr 2010 at 12:34pm
If I remember right someone mention a Caterpillar part number that matches up with the oxnard blade.
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF
Back to Top
skipwelte View Drop Down
Orange Level
Orange Level


Joined: 29 Oct 2009
Location: Anthon, Iowa
Points: 723 		Post Options Post Options   Thanks (0) Thanks(0)   Quote skipwelte Quote  Post ReplyReply Direct Link To This Post Posted: 07 Apr 2010 at 2:26pm

Cutting edges have a  standard hole pattern.  They come in 6, 7, 8 ft lenghts,  any construction machy dealer espicially if they sell motor graders should be able to hook you up.  Just know the length you need.   HTH
Back to Top
Bill (E.C.MO) View Drop Down
Silver Level
Silver Level


Joined: 11 Sep 2009
Location: Missouri
Points: 135 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bill (E.C.MO) Quote  Post ReplyReply Direct Link To This Post Posted: 09 Apr 2010 at 3:57pm
Boomer,
 
The best and most reasonable source we have found for cutting edges, teeth, etc. (plus undercarriage parts and that sort of thing) is Cohn in Union, MO.  Try emailing our salesman Rick at rfreund@scohn.com or calling 800-351-2646
A-C's currently on the farm: B, CA, 2 D-17 D's, One Eighty, ass't implements.
Back to Top
Ron(MN) View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 15 Sep 2009
Location: Le Sueur MN
Points: 14 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ron(MN) Quote  Post ReplyReply Direct Link To This Post Posted: 09 Apr 2010 at 9:34pm
Ziegler Equipment is a CAT dealer in Minneapolis where I got a replacement cutting edge for mine Oxnard blade. Part number is 7T-1633 (6 foot). Their phone number is 800-352-2812. There is another one in Altoona, Ia...phone #800-342-7002. Mine cost just over $40.00 a couple years ago.
Good luck,
Ron
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum