This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Allis chalmers tracters
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
delbertstringer View Drop Down
Bronze Level
Bronze Level


Joined: 18 Feb 2010
Location: Nevada
Points: 1 		Post Options Post Options   Thanks (0) Thanks(0)   Quote delbertstringer Quote  Post ReplyReply Direct Link To This Post Topic: Allis chalmers tracters
    Posted: 18 Feb 2010 at 2:50pm
To whom it may concern, why wont my govener gear engage with my timming gear ? anyone have sugetions ?
allis chalmer WD45 Gas tracter
Back to Top
Sponsored Links


Back to Top
Chalmersbob View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Pennsylvania
Points: 2122 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Chalmersbob Quote  Post ReplyReply Direct Link To This Post Posted: 18 Feb 2010 at 8:36pm

How do you know the gear is not engaging?

The gear could be stripped, or a pin could have sheared off on the drive for the mag/distributor. The only way you are going to know for sure is to tear it apart and see what you find. Bob
Back to Top
Ken in Texas View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Henderson, TX
Points: 5919 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ken in Texas Quote  Post ReplyReply Direct Link To This Post Posted: 18 Feb 2010 at 8:49pm
I presume you took it apart and are trying to put it back together. Were they meshing correctly before you took it apart? 
Back to Top
DREAM View Drop Down
Orange Level
Orange Level
Avatar

Joined: 06 Jan 2010
Location: Elberton,GA
Points: 1828 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DREAM Quote  Post ReplyReply Direct Link To This Post Posted: 18 Feb 2010 at 8:58pm
Not sure if it's the same, but I had a problem with the mag on my C. The rotor button was not turning after I set the points and cleaned everything(this was when I first got it, trying to get it started for the first time.). Found that someone had left the gasket off between the points cover and rotor section. This caused the rotor gear not to mesh with the mag drive gear. I cut a gasket for it, solved the problem. Is the problem you're having that the rotor button won't turn, or can you not get the governor gear to go back into the timing gear? Is it binding and won't go into the hole?
Back to Top
Ken in Texas View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Henderson, TX
Points: 5919 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ken in Texas Quote  Post ReplyReply Direct Link To This Post Posted: 18 Feb 2010 at 9:12pm
The gears are not straight cut and its a little tricky to get the timing marks lined up. Maybe this is what the original poster is trying to say. I like to have gone nuts timing  a B because both the marks were on teeth and not on a tooth and a gullet.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.125 seconds.


Help Support the
Unofficial Allis Forum