This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
8050 Allis Chalmars |
Post Reply |
Author | |
8050allis!
Bronze Level Joined: 19 Feb 2024 Location: Sedgwick KS Points: 9 |
Post Options
Thanks(0)
Posted: 19 Feb 2024 at 10:29pm |
Ok guys I hope you can help me i got a 8050 Allis and why can’t I run to remotes at the same time I’m pulling a sprayer and I have the 1 remote in detent running the pump and I want to run the 2nd remote to run the booms up and down over terrises and stuff and when I engaged the 2nd remote it kills everything stops spraying and all! My 7060 ran 2 remotes all the time on this sprayer what’s wrong? Yes I have adjusted the flow and don’t help at all!
|
|
Sponsored Links | |
8070nc
Orange Level Access Joined: 21 Mar 2019 Location: North Carolina Points: 506 |
Post Options
Thanks(0)
|
This probably isnt your problem if you have had the tractor some time. I got a new to me 8070. The hoses from the valves to the couplers were hooked up wrong. Caused all kinds of problems
|
|
1984 80780
1957 D14 DES 300 with 25000 engine 616 tractor |
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8251 |
Post Options
Thanks(0)
|
I can't tell you what's wrong but the 2 tractors have basically the same hyd system so the 50 aught to do the same as the 60.
|
|
victoryallis
Orange Level Joined: 15 Apr 2010 Location: Ludington mi Points: 2876 |
Post Options
Thanks(0)
|
There is a set screw that will back out and cause your remotes to loose function. BTDT. My 8050 did that but had other issues so it landed at the dealer.
|
|
8030 and 8050MFWD, 7580, 3 6080's, 160, 7060, 175, heirloom D17, Deere 8760
|
|
8050allis!
Bronze Level Joined: 19 Feb 2024 Location: Sedgwick KS Points: 9 |
Post Options
Thanks(0)
|
Ok we’re is that set screw at?
|
|
randy
Orange Level Joined: 12 Sep 2009 Location: Illinois Points: 1185 |
Post Options
Thanks(0)
|
When i lift the booms up on the sprayer the pressure drops a little for just a second and then goes back to normal. And the valves stay in Detent.
I use the tractor valves to control the hyd flow to the pump and its seems to work ok. This is a 8050 and a Best Way sprayer.
|
|
CA WD WD45 D17 D17 Diesel 7060 8050 8070
|
|
Kevin in WA
Orange Level Access Joined: 08 Feb 2010 Location: Lynden, WA Points: 611 |
Post Options
Thanks(0)
|
I would start by checking your high pressure setting at the tee on the pto valve, it should be 2500 when you activate a remote, if it is low and the sprayer booms need more pressure than that it will just destroke the pump and you loose everything. I have seen broken springs in the compensator, or it may just be weak from age.
|
|
8050allis!
Bronze Level Joined: 19 Feb 2024 Location: Sedgwick KS Points: 9 |
Post Options
Thanks(1)
|
Ok well that helps me out what set screw are you talking about and were?
|
|
Ron(AB)
Orange Level Joined: 27 Dec 2009 Location: Alberta Points: 958 |
Post Options
Thanks(0)
|
On the valve stack, you will see three tubes with a little rubber plug on the end. Pull the plug out and you can put a screw driver in the hole to set the pressure.
|
|
405, 7000, 7050, 8050, 8070, L3, 2300 & 2600 disk
|
|
tbran
Orange Level Joined: 14 Sep 2009 Location: Paris Tn Points: 3300 |
Post Options
Thanks(0)
|
uploads/963/8000_2024-02-23_08-00-23.pdf
Attached is flow control with pilot check assembly drawing. When higher pressure function is used on another remote the common passage shifts this valve towards closed and restricts the flow, trying to maintain same flow thru smaller opening but at higher pressure. Drilling face allows some flow to continue even if valve totally closes.
The screw at the end of the valve under the rubber cap does set the detent pressure at which the valve kicks out. It will not set the main pressure. It can be screwed in so as not to kick out. Make sure the system standaby pressure is about 500 PSI
Edited by tbran - 23 Feb 2024 at 8:04am |
|
When told "it's not the money,it's the principle", remember, it's always the money..
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |