This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Allis Chalmers wd45 hand clutch |
Post Reply | Page <1 456 |
Author | |
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
I can make the gasket work
|
|
Sponsored Links | |
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
Is stop leak ok to use in the transmission clutch differential fluid and the hydraulic fluid
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20528 |
Post Options
Thanks(0)
|
NO. Use oil resistant RTV lightly rubbed onto the paper gasket.
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
Will any trans hydraulic fluid work.
I usually get harvest king at theisens |
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20528 |
Post Options
Thanks(0)
|
You can use about anything and it will be fine. Remember, it came with an 80/90 gear oil, so if you go to a lighter viscosity, there may be more leaks. Takes 4 to 4 1/2 gallons total into the two fill plugs on the left side.
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
Ok so 80/90 is best.
What if I go heavier. Also how many drain plugs are there I only did the hydraulic one and the one under the pto |
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20528 |
Post Options
Thanks(0)
|
If you did the hydraulic sump, that is another 6 quarts of hydraulic oil. Take out EVERY drain plug, which I think is FOUR.
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
So 4 including the 2 I did already
Can I get 80/90 gear oil still |
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
I'll try to get 80/90 but I might just get trans hydraulic fluid
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8241 |
Post Options
Thanks(0)
|
Only has to seal around the outside. I don't see what's different but it's too close for me to figure out. Pull the drain plugs and let it empty out. I think there's 2 under the trans/rear end. You can try to rinse it with diesel fuel. Put fresh trans-hydraulic fluid in all compartments and forget "stop leak". Everything except the engine can use one (same) fluid.
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
The new gasket doesn't have the bottom hole.
So I can use the oil I showed |
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8241 |
Post Options
Thanks(0)
|
The link don't work but it says hyd and trans so I'm guessing yes.
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
I'll double check the gasket later today when I go to bill deppes
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
Is there anything else I should know when I put the tractor back together other than to line up everything
|
|
WF owner
Orange Level Joined: 12 May 2013 Location: Bombay NY Points: 4667 |
Post Options
Thanks(0)
|
You need to align everything so it slips back together. You may have to put the PTO in gear and turn it to get the shafts aligned.
DO NOT PULL IT BACK TOGETHER WITH BOLTS!
|
|
hunter321
Orange Level Joined: 11 Jan 2021 Location: 52320 Points: 520 |
Post Options
Thanks(0)
|
The tractor is back together and the hand clutch works
|
|
Les Kerf
Orange Level Joined: 08 May 2020 Location: Idaho Points: 784 |
Post Options
Thanks(0)
|
WOOHOO!!! It would have taken me at least a week to do all of that! (I don't move quite as fast as I once did). Good job!
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8241 |
Post Options
Thanks(0)
|
Good to hear!
|
|
plummerscarin
Orange Level Access Joined: 22 Jun 2015 Location: ia Points: 3478 |
Post Options
Thanks(0)
|
|
|
Les Kerf
Orange Level Joined: 08 May 2020 Location: Idaho Points: 784 |
Post Options
Thanks(0)
|
There are precious few 17 year olds nowadays that would tackle a task like this. Keep up the good work!
|
|
Post Reply | Page <1 456 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |