1941 Wc Stock Puller

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Hi I'm new to this forum and I'm only 15 but I'm lucky enough to own a 1941 WC. I'm looking to build it into a puller and be somewhat competitive in my local club. I know pretty much nothing about pulling and need a lot of help. Money is not a huge factor but is something I have to consider. Any help would be GREATLY appreciated!

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Clay2017 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 18 Aug 2014 Location: Ohio Points: 20	Post Options Post Reply Quote Clay2017 Report Post Thanks(0) Quote Reply Topic: 1941 Wc Stock Puller Posted: 18 Aug 2014 at 9:50pm
	Hi I'm new to this forum and I'm only 15 but I'm lucky enough to own a 1941 WC. I'm looking to build it into a puller and be somewhat competitive in my local club. I know pretty much nothing about pulling and need a lot of help. Money is not a huge factor but is something I have to consider. Any help would be GREATLY appreciated!

Sponsored Links

bigcountry48 Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 28 Aug 2011 Location: Georgia Points: 1100	Post Options Post Reply Quote bigcountry48 Report Post Thanks(0) Quote Reply Posted: 19 Aug 2014 at 6:38am
	Start by finding a good used wd45 crankshaft and use that with those rods and pistons, make sure everything in the motor is nice and tight while you are replacing the crank. This crankshaft has a longer stroke, and you dont have to change anything in the motor to get it to work. that will create more torque. Also get as big a carburetor as you see fit probably a tsx464 would do you good. After all that get a 12 volt battery and a high performance coil along with a petronix system, these will help you run more efficiently while producing a little more horse power. Next you'll need some weight bars wheelie bars and most likely a new draw bar design. The closer and higher up the draw bar is the better (in theory, some will disagree its just what I've heard by the majority) pm me your number and ill text you some pictures of my weight bars just to get you started. Oh I almost forgot dont run the carb through the air cleaner, it restricts air. Go to your local auto parts store and buy the biggest air cleaner you can get that will work. You want as few bends in the line running to the carb as possible, bends restrict air. The longer the tube the more the air will spiral which will cause it to cool down and compress, which means more gas and air to the motor for more power. Hope this helps and if I'm unclear on something feel free to ask!
	1950 B, 1952 pulling wd, and 1954 wd45

dgerth Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 27 Nov 2012 Location: NC Wash Points: 172	Post Options Post Reply Quote dgerth Report Post Thanks(0) Quote Reply Posted: 19 Aug 2014 at 9:41am
	Then start stripping weight off to get as lite as possible. You remove the weight so that it can be put back on where it is needed the most to balance the tractor. A rough formula for this is 70-30. 70% on the rear and 30% on the front. Just think of the tractor as a teeter totter and find the balance point ;and then place the weights accordingly. It takes some practice but is crucial to successful pulling. Get the balance right coupled with good traction and you are well on your way in the sport of pulling. Good Luck and have FUN! dg

Clay2017 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 18 Aug 2014 Location: Ohio Points: 20	Post Options Post Reply Quote Clay2017 Report Post Thanks(0) Quote Reply Posted: 19 Aug 2014 at 10:50am
	What should I take off? Things like cultivator lifters pto? I still have the cast rear centers but I'm looking to get spoke wheels

DrAllis Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Points: 20549	Post Options Post Reply Quote DrAllis Report Post Thanks(0) Quote Reply Posted: 19 Aug 2014 at 6:43pm
	Remove anything that you don't need for Pulling. A "WC" is pretty light as it is, and you might want to actually use the PTO later for some tune-up/dyno time(IF you have access to a dyno). If your weight class is 3500 lbs and up, you won't need to remove much as long as the fluid is removed from the rear tires. Get your drawbar up to the maximum height allowed and as short as allowed. This is usually 20 inches high and 18 inches from the center of the rear wheels to the hitch point. These are standard dimensions but not always the Rule, depending on where you're competing. Having a way to add 500 lbs in 100 lb (or smaller) increments will allow you to pull a light class and then one heavier. It's always best to use suitcase style weights and be able to hang them on the front and rear of the tractor without any hassle doing so. General rule for me is when increasing my total weight by 500 lbs, I add 100 to 150 lbs to the front and 300 to 400 on the rear. This of course assumes my balance in the first class was correct. My front weights are 11 ft from the rear wheel center and rear weights are very close to the rear axle.