| Author |
 Topic Search  Topic Options
|
Hardwater000 
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Allis Chalmers b Ross steering box
Posted: Yesterday at 5:55am |
|
What type of seal is everyone using for the shaft that the steering wheel rides on, where it goes into the steering box (Ross)?
Tia
|
 |
|
Sponsored Links
|
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81221
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 8:42am |
some have a seal, some dont... i think its more to keep water from leaking down the shaft ??? Not a seal for the BOX...
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 9:02am |
|
Yes just to keep water out
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81221
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 9:28am |
|
Google search does not show that part number.. Sandy Lake or other AGCO dealer might be able to locate it... I think MOST people would get the ID and OD and just buy generic....i think i did that many years ago on one box... normally mine did not need replace..
Edited by steve(ill) - Yesterday at 9:29am
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 1:03pm |
|
Cr 7421 .75id 1.187id wat I measure we will see
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81221
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 hours 33 minutes ago at 3:33pm |
thats a good number... sounds close..... that seal is not very THICK ... but the OD and ID are right.
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 hours 30 minutes ago at 5:36pm |
|
Let's hope, I have looked at the book like u said that part number wasn't working and after I posted I decided to take it to work and measure it all and have another set of eyes to make sure a regular seal would work, most say to use felt... Really I'm worried more about outside leaking in more so than out.
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81221
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 hours 12 minutes ago at 5:54pm |
|
make sure there is a pin hole in the TUBE on the bottom, just above the seal... any rain / moisture that gets inside and runs down the tube should STOP at the seal and drain outward.... put a thimble full of grease all over the seal prior to sticking the shaft thru it.. The grease should be there forever and help the seal.
Edited by steve(ill) - 20 hours 10 minutes ago at 5:56pm
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 hours 5 minutes ago at 6:01pm |
|
I need to-do that I'm using PVC for the column, original was rusted out. I'm in the fitting stage not sure it will fit right and or look good.
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81221
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 hours 55 minutes ago at 6:11pm |
|
steel conduit is a good replacement... exact size.
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 hours 60 minutes ago at 9:06pm |
|
I have located some conduit in case this doesn't pan out. I hate to spend that kinda money on the regular bushing that the shaft rides in. I lucked into finding one that fits the PVC worked out perfect for that, the only thing that worries me is mounting the top around the throttle the regular mounts seem to fit it fine. I am missing the piece that the column sits on was missing when I bought the tractor so that will be another thing to build or try to locate.
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81221
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 hours 42 minutes ago at 9:24pm |
I hate to spend that kinda money on the regular bushing that the shaft rides in
I have made a couple in the past out of brozne, turned on the lathe... New ones seem to be nylon / plastic ....
--- 100 years ago they use to make bushing out of oak wood.. Maybe you could get a piece of oak ( fire wood) and drill a 3/4 inch hole in it and grind down the outside ? ... piece of ash from an old baseball bat ?
Edited by steve(ill) - 16 hours 6 minutes ago at 10:00pm
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 8 hours 52 minutes ago at 5:14am |
|
That's is a good idea, I didn't think of that. The tractor for the most part is waiting on the steering box to get sealed up (seal is ordered) so I can get it back together to fit the column. I hav took it all apart and wire brushes it all down to metal. Lol I went threw 2 angle grinders and numerous wire brushes after thought I shud have drug out the sandblaster. Just a ruff estimate with labor and parts I shud be just under 10,000 in it lol.jk thanks for the help Steve. U always take the time on any questions I have asked to give me and a lot of other people good answers and advice. I usually read a lot of post on here bf I ask anything...
|
|
