| Author |
 Topic Search  Topic Options
|
ChuckLuedtkeSEWI 
Orange Level
Joined: 11 Sep 2009
Location: Jackson, WI
Points: 1826
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Throttle linkage on D17 series 4
Posted: 24 Oct 2010 at 2:52pm |
|
On the throttle linkage on my D17 series 4, right underneath the gas tank, there is a small rod that comes forward that on the end has an end with a ball joint on it, that snaps into a socket piece for the next series of the linkage. this ball and socket piece is worn out and the ball falls out of the socket. I looked page by page under AGCO's online parts catalog, and could not find it listed on there. I was wondering if anyone knew if these two parts were available yet, or where I could go to find them. I would like to get this fixed before winter as the baler wire that was holding it doesn't let it pivot good, and I don't want it to be broken in the middle of winter as I use this tractor to clean the driveway. I will try to take a picture of the two pieces and post on here.
|
 |
|
Sponsored Links
|
|
|
ChuckLuedtkeSEWI
Orange Level
Joined: 11 Sep 2009
Location: Jackson, WI
Points: 1826
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 2:58pm |
|
|
|
R Aiken
Orange Level
Joined: 11 Sep 2009
Location: wc Ohio
Points: 1370
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 3:43pm |
|
I had one of those on my Case 830 . I took it off and put it in a vice and used a small punch and hammer to close the hole around the ball. My D17 is held togather with baleing wire also, has been good for years.
|
|
Russ-neia
Silver Level
Joined: 11 Sep 2009
Location: NE Iowa
Points: 489
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 3:50pm |
I bought one from my AGCO dealer a couple years ago. I'll look for a part number...
|
|
The innovators offer what others will imitate.
|
|
Russ-neia
Silver Level
Joined: 11 Sep 2009
Location: NE Iowa
Points: 489
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 3:55pm |
|
230339 would be a starting point...
|
|
The innovators offer what others will imitate.
|
|
ChuckLuedtkeSEWI
Orange Level
Joined: 11 Sep 2009
Location: Jackson, WI
Points: 1826
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 4:38pm |
|
Thanks Russ, I used the number and it pulled it right up. Now at least I can call and gasp when they tell me how much it will be!! That is if it's still available.
Edited by ChuckLuedtkeSEWI - 24 Oct 2010 at 5:11pm
|
|
1955 WD45 diesel 203322 was my dad's tractor, 1966 D15 23530, 1961 HD3 Crawler 1918, 1966 D17 IV 83495, 1937 WC 41255, 1962 D19 6221
|
|
John (C-IL)
Orange Level
Joined: 11 Sep 2009
Location: Illinois
Points: 1654
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 5:33pm |
|
I got 2 of them a year ago from my AGCO dealer. $11.24 each. I thought that was a pretty good price.
|
|
Matt MN
Orange Level
Joined: 14 Sep 2009
Location: Silver lake MN
Points: 1491
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 5:36pm |
|
I used a hammer and punch and pinched it together again. very easy to do.
|
|
Unless your are the lead horse the scenery never changes!!
|
|
Skyhighballoon(MO)
Orange Level
Joined: 11 Sep 2009
Location: Pilot Grove, MO
Points: 3115
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2010 at 7:40pm |
Mc-Master Carr has them for like $4-$5. Thanks for reminding me to put that on my next order. Mine came apart on my Series III D17 a couple months ago and I did exactly what Matt MN did to patch mine back together. He's a link to page at McMaster-Carr. Mike http://www.mcmaster.com/#ball-joints/=9f601aAlso reminds me I have to measure the ball joint ends on the steering drag link on my Allis 716H mower and get them too at Mc-Master Carr - same page. It too came apart about the same time!
Edited by Skyhighballoon(MO) - 24 Oct 2010 at 7:43pm
|
|
1981 Gleaner F2 Corn Plus w 13' flex
1968 Gleaner EIII w 10' & 330
1969 180 gas
1965 D17 S-IV gas
1963 D17 S-III gas
1956 WD45 gas NF PS
1956 All-Crop 66 Big Bin
303 wire baler, 716H, 712H mowers
|
|
