This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


D10 - D12 parts wanted
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Tracy Martin TN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tracy Martin TN Quote  Post ReplyReply Direct Link To This Post Topic: D10 - D12 parts wanted
    Posted: 15 Aug 2010 at 10:09pm
Looking for the hyd pump intake hose for series II or  III. Are the rubber dampners available for the PTO? Thanks Tracy Martin
Back to Top
Sponsored Links


Back to Top
Dusty MI View Drop Down
Orange Level
Orange Level
Avatar

Joined: 13 Sep 2009
Location: Charlotte, Mi
Points: 5058 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dusty MI Quote  Post ReplyReply Direct Link To This Post Posted: 16 Aug 2010 at 8:41am
Tracy, my local AGCO dealer did a nation wide check for the intake hose for my D-10 seres III, there were none available. 

I went to a local NAPA dealer they could get a hose that was similar. My hose had a large split in it. I got a piece of shrink tubing for electrical joints. I also used some Scotch Coat which is a liquid used for water proofing electrical joints. I coated my split hose with the Scotch Coat then put the shrink on and shrink it then applied another coat of Scotch Coat.

It's the same story on the dampers.

I have 1 in like new condition.    I WILL NOT PART WITH IT.

I made some out of neoprene. I can make some more. 

Dusty


Edited by Dusty MI - 16 Aug 2010 at 8:43am
917 H, '48 G, '65 D-10 series III "Allis Express"
Back to Top
Tracy Martin TN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tracy Martin TN Quote  Post ReplyReply Direct Link To This Post Posted: 16 Aug 2010 at 8:53am
Dusty, Thanks for your info. I sent you a PM also. Tracy Martin
Back to Top
Bob in King NC View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 25 Sep 2009
Location: King NC
Points: 2 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bob in King NC Quote  Post ReplyReply Direct Link To This Post Posted: 16 Aug 2010 at 9:22am
Tracy. if its the hose I'm thinking of. I go to local hyd dealer and get a piece of hyd hose and cut to correct length ,3/4 the best I remember and they sell spring that goes inside to keep from kinking. I have replaced 2 like this and have had no trouble over the past 7 or 8 years. My 2 cents, Bobby in King, NC.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.


Help Support the
Unofficial Allis Forum