| Author |
 Topic Search  Topic Options
|
SteveC 
Bronze Level
Joined: 11 May 2010
Points: 6
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: U-40 Power unit
Posted: 11 May 2010 at 6:59pm |
|
I have a U-40 Power unit. It runs good, starts after about two revolutions. It was used to power several grist mills. Any idea what it is worth? Would like to sell it. I also have three Meadows Grist mills (24",30" and a 36").Also have two line shafts, an elevator unit and belts.
|
 |
|
Sponsored Links
|
|
|
BrettPhillips
Orange Level
Joined: 11 Sep 2009
Location: Strasburg, VA
Points: 808
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 May 2010 at 7:18pm |
|
Where are you located?
|
|
SteveC
Bronze Level
Joined: 11 May 2010
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 May 2010 at 7:48pm |
|
NE Georgia, about 50 mile south of the NC line.
|
|
Fred in Pa
Orange Level
Joined: 13 Sep 2009
Location: Hanover Pa.
Points: 9210
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 May 2010 at 9:03pm |
|
Need more Info.
|
|
SteveC
Bronze Level
Joined: 11 May 2010
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2010 at 4:51pm |
|
What else would you like to know? Runs good, don't smoke, don't miss.
|
|
Fred in Pa
Orange Level
Joined: 13 Sep 2009
Location: Hanover Pa.
Points: 9210
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2010 at 7:35pm |
|
Electic start? side panels,Radi . condition . Picture. Phone #
|
|
SteveC
Bronze Level
Joined: 11 May 2010
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2010 at 8:24pm |
|
It's a hand crank start, not elec. Have both side panels, both in good condition. Radiator is good, not leaking. Condition is good, good compression, don't knock or smoke. 706-865-6459. Send me your Email address and I will send pictures
|
|
SteveC
Bronze Level
Joined: 11 May 2010
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2010 at 8:24pm |
|
Cleveland, GA 30528
|
|
TMiller/NC
Orange Level Access
Joined: 11 Sep 2009
Location: Lenoir, NC
Points: 1776
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2010 at 8:36pm |
Are the grist mills complete? Tim
|
|
SteveC
Bronze Level
Joined: 11 May 2010
Points: 6
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 May 2010 at 9:31pm |
|
I was wrong before. I Have a 20", 24", and a 30". The 24" is missing the metal hopper on the top. Everything else is complete. I was try to send pictures to others but having problems with my ISP provider, will have to call them tomorrow to see what the problem is. My number is 706-865-6459 if you have any questions.
|
|
