This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Troubleshooting: Starting WD-45
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
redshed60 View Drop Down
Bronze Level
Bronze Level


Joined: 29 Apr 2012
Location: Michigan
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote redshed60 Quote  Post ReplyReply Direct Link To This Post Topic: Troubleshooting: Starting WD-45
    Posted: 29 Apr 2012 at 1:59pm
A WD-45 has been sitting with fuel in the system for a two years, up here in the Great Lakes Northwoods....I'm the (proud) new owner with no experience with tractors.  I drained the tank, took off and cleaned the sediment bowl, and took the carb apart -- soaked the components in Berryman's, and put her back together.  The gaskets look good and the float is in good shape and hinges nicely with no effort.  The needle valve and bolt cleaned and varnish-free.  Newly added fuel appears to be flowing freely in the bowl - bottom bolt, when taken out, fuel flows out.

The electrical system is 12 volt, upgraded perhaps 3 or 4 years ago.  New battery cranks the engine over, compression seems good, but no spark when I took wire attached to  plug out, and tried to jump the spark to the block while the engine was turned over.  The plugs look good - not too much soot, ash,  or electrode degradation.

Checked all distributor connections.  The cap and rotor look new! 

Would appreciate any suggestions where to go from here.  Thanks!
Back to Top
Sponsored Links


Back to Top
CTuckerNWIL View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: NW Illinois
Points: 22825 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CTuckerNWIL Quote  Post ReplyReply Direct Link To This Post Posted: 29 Apr 2012 at 3:05pm
Do you have 12 volts to the coil when the key is turned on? 
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF
Back to Top
Thad in AR. View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Arkansas
Points: 9648 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Thad in AR. Quote  Post ReplyReply Direct Link To This Post Posted: 29 Apr 2012 at 3:09pm
As C Tucker says check voltage at the coil first. If this checks out the next step is the points and condenser.
Back to Top
redshed60 View Drop Down
Bronze Level
Bronze Level


Joined: 29 Apr 2012
Location: Michigan
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote redshed60 Quote  Post ReplyReply Direct Link To This Post Posted: 29 Apr 2012 at 4:46pm
Thanks, will check
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 29 Apr 2012 at 9:47pm
File the points.  MACK
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.047 seconds.


Help Support the
Unofficial Allis Forum