This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


WD45 Carb kit?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
79fordblake View Drop Down
Orange Level
Orange Level


Joined: 01 Jul 2010
Location: West Kentucky
Points: 827 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 79fordblake Quote  Post ReplyReply Direct Link To This Post Topic: WD45 Carb kit?
    Posted: 26 May 2011 at 9:32pm
I was wondering where is the best place to get a carb kit for my '57 Wd45? I don't want one of those cheap kits that come with half the stuff. I want everything, throttle shaft...etc.

It still runs and starts great but there is alot of slop in the throttle shaft and it runs a little rich and it doesn't respond much by playing with the screws.

I was looking at the online AC book and it doesn't show that there is any throttle shaft bushings? Just the packing and seals.
Back to Top
Sponsored Links


Back to Top
Tedin NE-OH View Drop Down
Silver Level
Silver Level


Joined: 30 Mar 2011
Location: OH
Points: 177 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tedin NE-OH Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2011 at 9:37pm
Call Sandy Lake Implement and talk to them 1-888-252-0656. Very knowledgable people
Back to Top
79fordblake View Drop Down
Orange Level
Orange Level


Joined: 01 Jul 2010
Location: West Kentucky
Points: 827 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 79fordblake Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2011 at 10:03pm
Anybody have a scanned manual for the old Zeniths and Marvel Scheblers? I have been looking on ebay for a original with no luck.

Ive read on a few other sites that the bore of the carb where the throttle shaft goes wears more than the shaft does. Are there bushings available? I have a drill press to drill the bores and can put in bushings(unless they are to delicate to be tapped in with a hammer?)
Back to Top
Steve in NJ View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Andover, NJ
Points: 11919 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Steve in NJ Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2011 at 11:56pm
That is correct. The bores do wear out before the shafts do. We offer rebuilding services and offer carb kits. Our kits do not come with new throttle shafts. Most of the time they are not needed. When I rebuild carbs for our customer's, I mic the shaft and then bore the worn throttle bore and fit the shaft to the new bushing and bore. Some bores I can use our new Polyethelene sleeves in. Works nice... Most kits run around $31. bucks. Gives you all the parts you need except the throttle shaft.
Steve@B&B
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.120 seconds.


Help Support the
Unofficial Allis Forum