This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Trip Beam Plow Question
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
KevinON View Drop Down
Orange Level
Orange Level


Joined: 07 Dec 2009
Location: Schomberg, ON
Points: 798 		Post Options Post Options   Thanks (0) Thanks(0)   Quote KevinON Quote  Post ReplyReply Direct Link To This Post Topic: Trip Beam Plow Question
    Posted: 30 Apr 2011 at 12:25pm
How tight should the main bolt that the stem pivots on be?  My stems wiggle a bit.  Thanks!
Back to Top
Sponsored Links


Back to Top
Chalmersbob View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Pennsylvania
Points: 2122 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Chalmersbob Quote  Post ReplyReply Direct Link To This Post Posted: 30 Apr 2011 at 9:50pm
bump
Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29792 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2011 at 6:46am
Just loose enough that when you pull the trip roller up by hand you should be able to pivot the moldboard back by hand. Is this a monoframe? On mine I had to disassemble the mechanism to clean it up enough so it would trip by hand. There are supposed to be washers on each side of the beam at the pivot but mine were just about completely worn away so I replaced them. Then I had to adjust the little coil trip spring pressure cause it tripped too easy. After adding a couple washers under one spring on one bottom they all four will trip nicely and only when I hit something and I still can lift the plow and trip them by hand. 
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
Amos View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Ontario
Points: 1318 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Amos Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2011 at 9:39am
The last monoframe plow I bought there are two trip mechanisms that have a bolt put into the mechanism, I am assuming this is to keep those moldboards from tripping.
Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29792 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2011 at 11:57pm
Originally posted by Amos Amos wrote:

The last monoframe plow I bought there are two trip mechanisms that have a bolt put into the mechanism, I am assuming this is to keep those moldboards from tripping.
Good way to eventually ruin the plow. Needs adjusting.
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum