| Author |
 Topic Search  Topic Options
|
7060 
Orange Level
Joined: 16 Sep 2009
Location: Missouri
Points: 1148
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 200 has no hydraulics
Posted: 14 Oct 2024 at 5:16pm |
|
I have a 200 that lost hydraulics and 3 point. It had milky oil in it when I got it and the power director valve and pto valve spools were sticking. I polished those up and I have everything but remotes and 3 point. I can move the traction booster lever and the 3 point raises though. Can I check pressure somewhere with the gauge?
|
 |
|
Sponsored Links
|
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 709
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2024 at 5:20pm |
|
Sounds like a plugged filter to me, have you changed it?
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4924
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2024 at 7:11pm |
|
You didn’t mention that you had changed the fluid and filter? Milky means water has got into the system which is why you have valves sticking most likely. If you haven’t I would do that first before you start troubleshooting. Fluid needs to be correct, make sure you clean the sump screen.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 709
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2024 at 7:37pm |
|
Might need to flush it?
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
7060
Orange Level
Joined: 16 Sep 2009
Location: Missouri
Points: 1148
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2024 at 7:43pm |
|
It has new agco 821xl and new filter.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20522
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 Oct 2024 at 8:27pm |
|
If the power steering and Power Director clutch work fine, I'd ask if the 3-point hitch, when fully lowered, will raise to the top with the engine running wide open and NO LOAD on the hitch ???
|
|
7060
Orange Level
Joined: 16 Sep 2009
Location: Missouri
Points: 1148
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Oct 2024 at 8:36am |
|
Three point won’t move at all. With a gauge plugged into the remote there is zero pressure with the levers either. The three-point will raise to the top if you move the traction booster lever. I swapped relief valves with the traction booster and nothing happened. Where could I tee the pressure gauge in? I don’t have a service manual for a 200.
Edited by 7060 - 15 Oct 2024 at 8:38am
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20522
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Oct 2024 at 8:54am |
|
There are two pumps. A main pump (about 18 GPM) and the Traction Booster pump (about 2.5 GPM). Obviously the Traction Booster pump works, albeit slow, like it should be. If the power steering, power director and PTO all work, the main pump is at least working some. The power steering should work good with the engine at 700-800 RPM. Does it ??? If so, I'd be pulling the priority valve spool out of the rear section of the pump and make sure it is free to slide. Don't lose the orifice washer. The first 5 to 8 GPM goes to steering, PD clutches and PTO. As the engine speeds up the remaining 12 GPM goes to the 3-point and remotes when the priority valve spool shifts.
|
|
