This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Long wheelbase 7020 |
Post Reply |
Author | |
Mikez
Orange Level Access Joined: 16 Jan 2013 Location: Usa Points: 8380 |
Post Options
Thanks(0)
Posted: 13 Sep 2023 at 10:50pm |
Looks like a long wheelbase 7020 on tractorhouse. Interesting looking. Check it out
|
|
Sponsored Links | |
Unit3
Orange Level Joined: 17 Oct 2009 Location: NC Iowa Points: 5532 |
Post Options
Thanks(0)
|
That took some fabricating. I wonder how that would ride? I’ve seen guys reverse the front axle, but I’ve never seen them do a modification like this.
|
|
2-8070FWA PS/8050PS/7080/7045PS/200/D15-II/2-WD45/WD/3-WC/UC/C
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20479 |
Post Options
Thanks(0)
|
Some short-line company made those (maybe not that one) many years ago that you swapped out the center tube for a repositioned one and then used your old knees. Seems like the square tube was just ahead of the rear pivot point instead of behind it.
|
|
scott
Orange Level Access Joined: 12 Sep 2009 Location: michigan Points: 2572 |
Post Options
Thanks(0)
|
the one with 8988 hrs?
|
|
Mikez
Orange Level Access Joined: 16 Jan 2013 Location: Usa Points: 8380 |
Post Options
Thanks(0)
|
Yup cedar falls Iowa
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81066 |
Post Options
Thanks(0)
|
how far forward was the axle moved... i had a hard time seeing much difference ?
|
|
Like them all, but love the "B"s.
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20479 |
Post Options
Thanks(0)
|
Like I say, the square tube is ahead of the rear pivot, so I think it was about a 10 inch extension of wheelbase.
|
|
Ray54
Orange Level Access Joined: 22 Nov 2009 Location: Paso Robles, Ca Points: 4508 |
Post Options
Thanks(0)
|
Any ideas on why this was done? As the Doc has said a company did more than just one or two. As ride quality was already mentioned, from experience a little bit makes a lot of difference.
There was a good sized construction company here in California build 1000's of miles of highway. They became the go to for concrete paving for a time. But after a few years all the expansion joints became high spots. Some vehicles rode much, much better than other many times just to due with the wheel base. Many a independent trucker specked trucks the with the wheel base that gave less bucking rolling over the expansion joints. I was told just 2 inches more or less made a huge difference. The state spend a fortition planning the concrete for years. Finally in the last 20 years all has been replaced with asphalt concrete.
|
|
8070nc
Orange Level Access Joined: 21 Mar 2019 Location: North Carolina Points: 505 |
Post Options
Thanks(0)
|
We had a 8070 in the early 90s that we turned the front axle around on and made it look like that. Dont remember why we did it but I think it was to get clearance for saddke tanks. Wasnt ideal but it worked
|
|
1984 80780
1957 D14 DES 300 with 25000 engine 616 tractor |
|
victoryallis
Orange Level Joined: 15 Apr 2010 Location: Ludington mi Points: 2876 |
Post Options
Thanks(0)
|
Doesn’t look horrible. What was the logic I wonder.
|
|
8030 and 8050MFWD, 7580, 3 6080's, 160, 7060, 175, heirloom D17, Deere 8760
|
|
Mikez
Orange Level Access Joined: 16 Jan 2013 Location: Usa Points: 8380 |
Post Options
Thanks(0)
|
Wasn’t there posts on here awhile ago on doing this to 8xxx to make them ride better
|
|
MikeKroupa
Bronze Level Access Joined: 12 Sep 2009 Location: pierce,nebraska Points: 77 |
Post Options
Thanks(0)
|
If I'm thinking right DAKON mfg. made those kits to increase wheelbase. John Day Co. in Omaha was one of their distributors. I have the literature piece , just have to find it., Mike
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4910 |
Post Options
Thanks(0)
|
Oddly, my buddies Ford 8600’s are like that. He flips every one of his around for shorter wheelbase and a tighter turning radius.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Jordan(OH)
Orange Level Joined: 11 Sep 2009 Location: Celina, OH Points: 1547 |
Post Options
Thanks(0)
|
Those Fords came either way from the factory.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |