This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


670T Crank Pulley
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
smitty78 View Drop Down
Bronze Level
Bronze Level


Joined: 26 Apr 2015
Location: Okla
Points: 91 		Post Options Post Options   Thanks (0) Thanks(0)   Quote smitty78 Quote  Post ReplyReply Direct Link To This Post Topic: 670T Crank Pulley
    Posted: 25 Apr 2018 at 8:16pm
L2 Gleaner with 670T - crank pulley shivs had slipped a bit so sent it to Dale mfg, beautiful repair and priced right.  A few hours later usage noticed the inner hub had cracked.  Wondered if I over torqued the bolt and the tapered shaft made it fail ?  Does anyone know the torque spec on the crank pulley bolt ?

thanks, smitty  
Back to Top
Sponsored Links


Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 25 Apr 2018 at 9:29pm
220ft lbs.torque with all oil removed from both. Dry.    MACK
Back to Top
smitty78 View Drop Down
Bronze Level
Bronze Level


Joined: 26 Apr 2015
Location: Okla
Points: 91 		Post Options Post Options   Thanks (0) Thanks(0)   Quote smitty78 Quote  Post ReplyReply Direct Link To This Post Posted: 25 Apr 2018 at 9:43pm
So, the crank & hub tapered surfaces should be un lubricated during torque ?
Back to Top
SteveM C/IL View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8246 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SteveM C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 25 Apr 2018 at 11:30pm
That's what Mack said.
Back to Top
smitty78 View Drop Down
Bronze Level
Bronze Level


Joined: 26 Apr 2015
Location: Okla
Points: 91 		Post Options Post Options   Thanks (0) Thanks(0)   Quote smitty78 Quote  Post ReplyReply Direct Link To This Post Posted: 28 Apr 2018 at 6:10am
I was able to remove my 4 groove crank pulley without removing the radiator which was lucky but now having a hard time finding a replacement.  New over $1,500 (nearing value of entire combine, LOL), used $660, ouch.

New 3 groove around $500, but can you drive the alternator with just 1 belt and will it line up ?

Why don't those aftermarket monkeys offer a 4 groove ?  I'm not sure I've ever even seen a 3 groove setup, most are 4.  

Anybody have a 4 groove for sale ?

Notice the crack in the inner hub aligns with keyway and threaded hole ... perhaps a weak path


Thanks,

smitty







Edited by smitty78 - 28 Apr 2018 at 6:21am
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 28 Apr 2018 at 10:33pm
I may have one on a L2 motor. Will check.    MACK
Back to Top
smitty78 View Drop Down
Bronze Level
Bronze Level


Joined: 26 Apr 2015
Location: Okla
Points: 91 		Post Options Post Options   Thanks (0) Thanks(0)   Quote smitty78 Quote  Post ReplyReply Direct Link To This Post Posted: 29 Apr 2018 at 9:38pm
duh ... answered my own question ... the 3 groove pulley is a tractor application with the single belt driving the AC compressor, likely was more field demand than the 4 groove in which 2 belts drive the hydraulic pump. I imagine 1 belt would drive the hydraulic pump but the shivs wouldn't match (AC belt is thinner than hyd belts) so I'll keep looking for a 4 groove. Almost bought an L2 for parts saturday at a sale, was hung on 1K for awhile but ended up at 3K per a good auctioneer.

Edited by smitty78 - 29 Apr 2018 at 9:43pm
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum