This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


6060 ?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Jim in SE ND View Drop Down
Silver Level
Silver Level


Joined: 19 Jun 2010
Points: 61 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jim in SE ND Quote  Post ReplyReply Direct Link To This Post Topic: 6060 ?
    Posted: 19 Jul 2010 at 9:14pm
Did the 6060 require the same update on the front of the crankshaft to help prevent the bearing failure that the 6080 had? thanks
Back to Top
Sponsored Links


Back to Top
AllisFreak MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 07 Dec 2009
Location: Minnesota
Points: 1553 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AllisFreak MN Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2010 at 9:28pm
Yes.
'49 A-C WD, '51 A-C WD, '63 A-C D17 Series III, 1968 A-C One-Seventy, '82 A-C 6060, '75 A-C 7040, A-C #3 sickle mower, 2 A-C 701 wagons, '78 Gleaner M2
Back to Top
ScooterBuck View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 19 Oct 2009
Points: 76 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ScooterBuck Quote  Post ReplyReply Direct Link To This Post Posted: 20 Jul 2010 at 9:21pm
Does anyone have a picture of that update that they could post on this thread?
Back to Top
AllisFreak MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 07 Dec 2009
Location: Minnesota
Points: 1553 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AllisFreak MN Quote  Post ReplyReply Direct Link To This Post Posted: 20 Jul 2010 at 9:47pm
Can't post pics but can tell you that it is a bracket bolted in front of the crank pulley. Appears to be bolted to the engine block in three places. The bracket has a grease fitting in the lower front. It holds the crank in position so when the PTO clutch is disengaged it does not put too much foreward pressure on the crankshaft, taking out the crank bearings. Apparently the 433T & 433I engines were not designed to be in a tractor with a clutch putting foreward pressure on the crank shaft as they did not have thrust bearings. They were meant to be in belt drive applications such as combines and dozers.
'49 A-C WD, '51 A-C WD, '63 A-C D17 Series III, 1968 A-C One-Seventy, '82 A-C 6060, '75 A-C 7040, A-C #3 sickle mower, 2 A-C 701 wagons, '78 Gleaner M2
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.055 seconds.


Help Support the
Unofficial Allis Forum