![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
B front crankshaft seal |
Post Reply ![]() |
Author | |
Dale Ms ![]() Bronze Level ![]() Joined: 08 Jul 2024 Location: Mississippi Points: 4 |
![]() ![]() ![]() ![]() ![]() Posted: 08 Jul 2024 at 12:33pm |
I have a CE engine # 91611 K. Can’t locate a front oil for it. I see seals for later model of the CE engines. The part # in my parts book is 206593. I’ve been looking by putting 70 in front the parts #. No luck. Anybody know know what seal may go in that engine. Have tried part # 70225806. It didn’t fit. Any help is appreciated. I mow with this tractor an grass is growing.
|
|
![]() |
|
Sponsored Links | |
![]() |
|
steve(ill) ![]() Orange Level Access ![]() ![]() Joined: 11 Sep 2009 Location: illinois Points: 79854 |
![]() ![]() ![]() ![]() ![]() |
i think your shaft is 1.500 and the housing bore is 1.938 inch..(1-15/16).... the seal you can get is a 1.942 OD ....... check these out...
Edited by steve(ill) - 08 Jul 2024 at 1:24pm |
|
Like them all, but love the "B"s.
|
|
![]() |
|
Dale Ms ![]() Bronze Level ![]() Joined: 08 Jul 2024 Location: Mississippi Points: 4 |
![]() ![]() ![]() ![]() ![]() |
Thanks Steve for the reply. I’ve tried that size seal . It fits the shaft but not the bore. I measure the bore at 1.922. I’ll measure again to double check later this afternoon.
|
|
![]() |
|
steve(ill) ![]() Orange Level Access ![]() ![]() Joined: 11 Sep 2009 Location: illinois Points: 79854 |
![]() ![]() ![]() ![]() ![]() |
i thought the OLD BORE was 1.938 and the NEW BORE was 2.010 inch ??
I will double check for more info..
|
|
Like them all, but love the "B"s.
|
|
![]() |
|
PaulB ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4609 |
![]() ![]() ![]() ![]() ![]() |
There were 3 different seals used throughout production of the BE/CE engines. Even if you use the serial number on the block, you can not be sure of which seal the engine uses as often parts get updated over the years when doing repairs.
This is what I will do with every engine I rebuild, I install a speedi-sleeve over the grooves in the crankshaft and use a modern lip seal instead of the solid rubber or cork ones that come with today's gasket sets.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
![]() |
|
Dale Ms ![]() Bronze Level ![]() Joined: 08 Jul 2024 Location: Mississippi Points: 4 |
![]() ![]() ![]() ![]() ![]() |
Thanks guys . Sorry for being slow getting back to y’all. Think my plan moving forward is to purchase a common seal an have a machinist fit it to the timing cover. Paul, there are no return oil groves on the crank Probably not an original crank. Will have to put this project on the back burner. Had a D15 present with an electrical issue. It’s always something. I’ll holler to y’all later on . Thanks
|
|
![]() |
|
steve(ill) ![]() Orange Level Access ![]() ![]() Joined: 11 Sep 2009 Location: illinois Points: 79854 |
![]() ![]() ![]() ![]() ![]() |
Dale, there have been several guys that bought the NEW seal with the 2.010 OD and had the front cover machined to FIT that seal...
|
|
Like them all, but love the "B"s.
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |