This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Shops, Barns, Varmints, and Trucks
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


I600 hydraulic problems
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Thad in AR. View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Arkansas
Points: 9417 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Thad in AR. Quote  Post ReplyReply Direct Link To This Post Topic: I600 hydraulic problems
    Posted: 02 Jun 2024 at 8:27pm
First, one of the outrigger cylinders is leaking. It has the end cap welded on and the weld is leaking.
How should I go about fixing this?

Second, the Cessna rotary swing cylinder started leaking top and bottom.
Where can I get parts?
Back to Top
Sponsored Links


Back to Top
desertjoe View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 23 Sep 2013
Location: New mexico
Points: 13528 		Post Options Post Options   Thanks (0) Thanks(0)   Quote desertjoe Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2024 at 8:32am

 Hey Thad,,, I went thru similar repairs on the rotary swing cylinder and one of the backhoe's cylinders on my tractor some years ago,,,I went back to try to find my write up but couldn't find it,,,,WTH,,,,???
 There was a gentleman on here that I bought the new seals from for a complete overhaul of that rotary cylinder and his name and address were in my thread,,,(hope he's still around)
 
Back to Top
Thad in AR. View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Arkansas
Points: 9417 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Thad in AR. Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2024 at 11:43am
Originally posted by desertjoe desertjoe wrote:


 Hey Thad,,, I went thru similar repairs on the rotary swing cylinder and one of the backhoe's cylinders on my tractor some years ago,,,I went back to try to find my write up but couldn't find it,,,,WTH,,,,???
 There was a gentleman on here that I bought the new seals from for a complete overhaul of that rotary cylinder and his name and address were in my thread,,,(hope he's still around)
 

Yes hoping
Back to Top
Thad in AR. View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Arkansas
Points: 9417 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Thad in AR. Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2024 at 3:52pm
I once saw a write up on converting one of these to cylinders. Anybody know anything about that?

Edited by Thad in AR. - 03 Jun 2024 at 6:34pm
Back to Top
Thad in AR. View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Arkansas
Points: 9417 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Thad in AR. Quote  Post ReplyReply Direct Link To This Post Posted: 04 Jun 2024 at 12:51pm
I found an Agco parts number 837180M92
$736.00
Is there a way to see if this is correct?
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41484 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 10 Jun 2024 at 12:27am
The end cap on cylinder seems to be a common problem and clean and weld it up is the solution . On my hoe off my HD4 both cylinder end caps cracked next to barrel of cylinder , I just v ground the joint and welded it up without disassembling cylinder by moving piston to full extend . 
 Left some posts on your other post on the Cessna motor 
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
Back to Top
Thad in AR. View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Arkansas
Points: 9417 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Thad in AR. Quote  Post ReplyReply Direct Link To This Post Posted: 10 Jun 2024 at 5:22am
Originally posted by Coke-in-MN Coke-in-MN wrote:

The end cap on cylinder seems to be a common problem and clean and weld it up is the solution . On my hoe off my HD4 both cylinder end caps cracked next to barrel of cylinder , I just v ground the joint and welded it up without disassembling cylinder by moving piston to full extend . 
 Left some posts on your other post on the Cessna motor 

So I don’t have to disassemble the cylinder?
I’ll give this a try.
Thank you Coke.
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41484 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 10 Jun 2024 at 11:37am
With cylinder off machine and ports open so any content left in cylinder can gas off , just clean up area and V out part of old weld and carefully lay a bead over area for repair . 
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
Back to Top
Thad in AR. View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Arkansas
Points: 9417 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Thad in AR. Quote  Post ReplyReply Direct Link To This Post Posted: 13 Jun 2024 at 5:19am
Originally posted by Coke-in-MN Coke-in-MN wrote:

With cylinder off machine and ports open so any content left in cylinder can gas off , just clean up area and V out part of old weld and carefully lay a bead over area for repair . 

Thank you Coke.
I’ve been using it hard lately . Things are starting to show their age.
I have some work to do for sure.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.082 seconds.


Help Support the
Unofficial Allis Forum