This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


D19 Bull Pinion
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
JCinPA View Drop Down
Silver Level
Silver Level
Avatar

Joined: 12 Sep 2009
Location: Turbotville,Pa.
Points: 75 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JCinPA Quote  Post ReplyReply Direct Link To This Post Topic: D19 Bull Pinion
    Posted: 28 Mar 2010 at 6:04pm
Need help fellas.   I'm lookin for a Bull Pinion For My D19.  Any leads would be appreciated.  Thanks in advance.  JCinPA
Back to Top
Sponsored Links


Back to Top
DSeries4 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7369 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DSeries4 Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2010 at 9:49pm
Would one from a 190 work?  Just curious.
Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29782 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2010 at 9:54pm
I think the early straight 190 would work or an early xt gasser. Diesels xt's had a field installed updated rear end.
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
DSeries4 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7369 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DSeries4 Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2010 at 10:19pm
The gears on my XTD are flaking a little bit.  I am planning to rotate them so that the backside gets used.  There is still lots of metal there.
 
Might be sometihng for you to consider too if they are not too worn.
Back to Top
JCinPA View Drop Down
Silver Level
Silver Level
Avatar

Joined: 12 Sep 2009
Location: Turbotville,Pa.
Points: 75 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JCinPA Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2010 at 4:38pm
I have been told that the bull pinion from a One Ninty will work but need to be carefull to get same tooth count or replace both sides.   I'm gonna look it over close to see if reversing is an option.  Thanks for the sugestions  JCinPA
Back to Top
Gary IN View Drop Down
Orange Level
Orange Level


Joined: 13 Sep 2009
Points: 453 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary IN Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2010 at 8:33pm
Have a parts D-19 trans and rearend good. North East Indiana. if you can't find one closer. Gary IN
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.082 seconds.


Help Support the
Unofficial Allis Forum