This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


HD 5 Main Clutch
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
BFC View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 28 Sep 2024
Location: Ada Mn
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BFC Quote  Post ReplyReply Direct Link To This Post Topic: HD 5 Main Clutch
    Posted: 05 Oct 2024 at 6:39pm
I recently bought a Hd 5 crawler. I'm looking for supplier of clutch parts a yoke # 053925.
Looking for information on removing the yoke. 
Can it be done by leaving the housing in place or would you have to remove the part from the crawler?
Back to Top
Sponsored Links


Back to Top
gemdozer View Drop Down
Orange Level
Orange Level


Joined: 17 Sep 2009
Points: 989 		Post Options Post Options   Thanks (1) Thanks(1)   Quote gemdozer Quote  Post ReplyReply Direct Link To This Post Posted: 05 Oct 2024 at 8:32pm
I am not sure if you can removed the yoke with out removing the cluch belhousing and master cluch ,the yoke have a short shaft each side with key way 
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41600 		Post Options Post Options   Thanks (1) Thanks(1)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 06 Oct 2024 at 4:06pm
Remove bell housing , remove full clutch assembly , disassemble on bench and find the parts you need . I ended up turning the brass sleeve myself to replace worn one in my machine . Also check pins on the over-center linkages and the arms themselves for wear 
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
Back to Top
BFC View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 28 Sep 2024
Location: Ada Mn
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BFC Quote  Post ReplyReply Direct Link To This Post Posted: 06 Oct 2024 at 5:53pm
Thankyou for quick response, on my question.
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41600 		Post Options Post Options   Thanks (1) Thanks(1)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 07 Oct 2024 at 6:57pm
The clutch friction material also needs to be checked and rivets holding it , the disc if it has dampening springs also need checking . I replaced a couple discs ad last time I went to bi-metallic disc . Same as the HD11 steering clutches I used rather than fiber discs . 
 It may be necessary also to check flywheel and friction face of clutch to see if they need resurfacing . 
 Replace the bearing in the crankshaft with new sealed bearing , making sure crankshaft wick fitting is plugged . Original pilot bearing was lubed from drilled hole in crank, by using sealed bearing no oil is introduced into clutch housing area . 
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
Back to Top
gemdozer View Drop Down
Orange Level
Orange Level


Joined: 17 Sep 2009
Points: 989 		Post Options Post Options   Thanks (1) Thanks(1)   Quote gemdozer Quote  Post ReplyReply Direct Link To This Post Posted: 08 Oct 2024 at 10:20am
If you removed the belhousing and cluch assambly you need to removed the cluch bolts first
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum