wd sleeve

can someone tell me ..what the size of the out side of the sleeves of a wd is..i  have frend  wanting to put  cummins pistons in  my old wd motor ...thanks

would like all  measuremets on the out of the sleeve..tks

thanks wi50  ...  wouild u like to do a  e  motor  some time for me ..thanks  will give u my number some time....   gblu

DONT mismeasure    

CTuckerNWIL wrote: "outside bore sleeve" Been around a shop and machine tools for 40 years and never heard of an outside bore sleeve

Like spankanomics, but spankalanguage... Outside bore, forged cast rods..

I think we should rename eddies speed shop to eddies stroke and poke. Stroken and pokin the keyboard, it's what we do best, cause we sure dont know how to run a machine.

mlpankey wrote: never hear od outside diameter and id inside diameter.   some people just walk in and say hello at machine shops and its evident  which ones they are  cause they cant do machine work . cause they would have to remove their nose from a dictionary to do any work.

So what is outside bore sleeves? Machinists turn OD's and bore ID's but I suppose if you're backwoods enough, you could bore an OD if that's what you want to do. I have real pictures of some of my machining work. What do you have pictures of besides welding a front pulley to balance the crankshaft?

I remember that, Rod! No, he's taking " orders" for Ross pistons, trying to act like he's a Ross dealer.. It's funny, cause there are too many people who know he's lying about THAT too...People know each other, Pank . People know each other...

c tucker said he wanted to see something i machined so i replied . it would be nice if some could read.

Edited by mlpankey - 29 Mar 2013 at 8:16pm

THE-MAN wrote: I remember that, Rod! No, he's taking " orders" for Ross pistons, trying to act like he's a Ross dealer.. It's funny, cause there are too many people who know he's lying about THAT too...People know each other, Pank . People know each other...

since you are the man in the know tell me whos motors ive done and are doing . you will also know that i sold dakin arias pistons and my personal build i used j and e . barney and ray both ross dealors as well either one can vouch for that so i dont need someone to order my parts i do well at finding useful part numbers . infact i do so well at it that most of you guys pen the part numbers i post  down and repost them as your own after trying to comvience others they dont work. believe me if getting a set of pistons to cut cost for a guy from a fellow dealor is a issue . i will just order from the factory as i have in the past cause its nothing to me cost gets past on. price in cost being a dealor of all three instead of reducing cost purchasing soley from one .  you guys should be thinking me for posting old build part numbers for it takes hours online and measuring researching to find manufactures and then the manufacturer or warehouse with the best deal.  Then machining to fit when installing or opertaing clearances once it arrives like sleeve stock and valve guide stock .

Edited by mlpankey - 29 Mar 2013 at 8:49pm

THE-MAN wrote: Musta hit a good nerve. Nice long explanation trying to cover your butt..

nope no nerve hit just tired of the scoffers and liers using my knowledge and work for free . just pull all my work back to my shop not share purchasing power with anyone and cost well be passed along . you would think anyone could call a piston manufacture give them the bore size ring sizes and placement along with wrist pin size but you will be surprised at how many on here either cant or wouldnt and that to eliminates purchasing power quantities

Edited by mlpankey - 29 Mar 2013 at 9:01pm

Here's a bit of my machine work, this one runs better than spankeys imaginary engines.



Couple guys on here seen this baby run..

Spunky that's a nice piece of aluminum ya got there in the lathe, serious turning there man....

Pank, as I remember, dakins motor blew up or had catastrophic problems.

Wow. Moly 1/16, 1/16 x 3/16 rings in 4.125 bore can be bought for as little as $60 and up for 8 cyl set. That's $8 a hole round here.

post the supplier for total seal gapless rings at that price rod so your not just talking .