This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Learning how to plow |
Post Reply | Page 12> |
Author | |
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
Posted: 14 May 2024 at 3:12pm |
1. I purchased a Case 3 bottom 16" moldboard plow.
2. Since this is not a snap coupler plow, I'm thinking that I need to use the position control to regulate the depth of the plow. When I drop the plow to the ground and start forward with the tractor, the 3 point hitch arms stay at the predetermined level, but the plow trys to go to the center of the earth, raises the front end off the ground, and spins out. 3. This probably should have been my first statement, this is a gasoline WD45. Do I need to install a gauge wheel on the plow to prevent it from going to deep? 4. The tires are filled with calcium, but I don't believe to the max. 5. Any suggestions on what I need to do different? Thanks, JL
|
|
Sponsored Links | |
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 80828 |
Post Options
Thanks(0)
|
when you set the plow on the ground, how HORIZONTAL is the bottom relative to the ground ? ........ You can adjust your TOP LINK if your digging in too much.
|
|
Like them all, but love the "B"s.
|
|
ac45dave
Orange Level Access Joined: 23 May 2015 Location: SE(IN) Points: 1337 |
Post Options
Thanks(0)
|
This video does a good job on plow set up. http://www.youtube.com/watch?v=NjZSTwJ3laI
|
|
54 wd-45gas ; 56 wd-45d N/F w/fact p/s ; 63 d-17 sIII N/F gas ; 60 D14 N/F ; 67 d-17 sIV N/F gas ; 63D15 sII W/F; 39rc#667 ; 2021 massey 4710 fwa ; gravely 2 wheel tractors
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20398 |
Post Options
Thanks(0)
|
A WD-45 doesn't have a "depth" control. The plow needs a slip heel on the rear bottom or a tire beside the rear bottom. Traction Booster system must be working properly (if it can) with your type of 3 point hitch. Rear wheels must be set to correct width. 3 x 16's on a WD-45 in some soils may be too much plow.
|
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I have the plow level on both axis. I've not went far enough to have to compensate for the wheels being in the furrow. If I lengthen the top link, won't that just put the rear bottom deeper?
|
|
PaulB
Orange Level Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4707 |
Post Options
Thanks(0)
|
#1 if possible, find an operators manual for your Case plow
#2 access how worn out the landslides are. Worn landslides will allow the plow to track towards the land. #3 most 3pt plows have the ability to alter the orientation of the pullbar to help center the draft: Refer to operators manual. #4 Go find a snap coupler plow.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 80828 |
Post Options
Thanks(0)
|
are all three digging in together... or is the FRONT digging while the back slip heal is still setting on the ground ?
|
|
Like them all, but love the "B"s.
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20398 |
Post Options
Thanks(0)
|
Add-on 3-point hitches are sometimes not really well designed. By that I mean the actual length of the draft/pull arms may be too long, moving the plow farther away from the tractor, which makes it pull harder. Lengthening the top link will tend to "nose up" the plow, which will help keep it from sucking itself too deep making it too much load for your tractor. Pretty easy to give the top link a couple of turns longer at a time and see what it does for you.
|
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I enjoyed the video, and looking forward to trying the plow settings that were demonstrated. I have come to the conclusion that I need a gauge wheel by the rear molboard.
Thanks for the input. JL. |
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I agree that controlling the rear molboard is my priority right now, before I can work on other adjustments. Tell me about the slip heel, I don't know as I understand what that is?
Thanks, JL |
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I would love to find a snap coupler plow!
|
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
They all seem to be going in together.
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 80828 |
Post Options
Thanks(0)
|
I have come to the conclusion that I need a gauge wheel by the rear molboard.
the HEEL , like on your foot , is at the back and keeps you from sinking into the ground... as you said... a WHEEL serves the same purpose..
|
|
Like them all, but love the "B"s.
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20398 |
Post Options
Thanks(0)
|
None of the older snap-coupler plows had a depth wheel on them. They had a slip heel on the rear plow bottom. I have both types and they both work well if one knows how to adjust the plow. Why you wouldn't re-try your plow by lengthening the top link is beyond me. It's easy to do and costs NOTHING. Also, does your 3-pt hitch activate the Traction Booster system or not ??????? It is a tremendous advantage to have the Traction Booster working, especially with a plow that may be 6 inches too wide of cut for a WD-45 tractor.
|
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
So is this something different than the landside, or is it like a skid plate that attaches to the landside?
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 80828 |
Post Options
Thanks(0)
|
GOOGLE....
AI Overview Yes, the rear bottom end of a landslide that rubs against the furrow sole is known as the heel of a plow. The heel is used in plows that don't have a rear furrow wheel. Some plows have a cast-iron slip heel that can be easily replaced. Edited by steve(ill) - 14 May 2024 at 10:46pm |
|
Like them all, but love the "B"s.
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8218 |
Post Options
Thanks(0)
|
Tell us about the hitch you have. Where / what is it attatched to to pull? Maybe it renders your traction booster useless. That would not lead to success with a 3pt plow especially.
|
|
Steve A
Silver Level Joined: 12 Apr 2012 Location: NLP Mi Points: 215 |
Post Options
Thanks(0)
|
Post some pictures of the 3 pt hitch, back of the tractor--especially where the top link is hooked up, the plow, etc.
|
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I will try to get some pics tomorrow.
|
|
AC7060IL
Orange Level Joined: 19 Aug 2012 Location: central IL Points: 3335 |
Post Options
Thanks(0)
|
Your WD45’s right side tire(s) should be running in plow furrow ~ correct? If yes, adjust tractor’s right side wheels outward to allow 16” bottom width measured from inside wall of right rear tire to landside of 1st bottom.
Then 3pt hitch’s lower draft arms need to be adjusted to proper heights to allow plow to run level while tractor is operating with right tire(s) in plow furrow. To do this, set lower left draft arm at its lowest height setting. Then set lower right draft arm about 2” higher from its lowest height setting. Now with plow initially leveled but slightly tilted upward on its right side, lower plow into unplowed field to create first pass. There is no furrow, so right side of plow will be running shallow. That’s ok. Plow will not be as difficult to pull. And this first pass shouldn’t ridge up as bad on its right side? After plowing 50’ or so, operator can then stop & adjust plow’s rear depth to attain 7”? 8”? or whatever furrow depth is desired. For front of plow depth, use tractor’s traction booster. Now plow has been initially leveled from front to rear. Once a furrow has been created, plow’s left to right level & front to back level can both be tweaked as needed. Edited by AC7060IL - 16 May 2024 at 7:17am |
|
rtwfarm
Orange Level Joined: 26 Feb 2012 Location: nebraska Points: 1284 |
Post Options
Thanks(0)
|
Have several snap coupler plows 402-469-1738 cheap
|
|
Tbone95
Orange Level Access Joined: 31 Aug 2012 Location: Michigan Points: 11589 |
Post Options
Thanks(0)
|
Well it’s only been like 6 hours, and now it’s dark, so maybe he’ll try it, give him some time. |
|
Oldwrench
Bronze Level Joined: 12 Jan 2020 Location: Northeast Points: 129 |
Post Options
Thanks(0)
|
Here is a semi-mounted snap coupler plow with a tail wheel. It is in central NY though. |
|
IBWD MIke
Orange Level Joined: 08 Apr 2012 Location: Newton Ia. Points: 3684 |
Post Options
Thanks(0)
|
A good snap-coupler plow would be the best solution as others have alluded to. However, his location is a complicating factor. Seems like there is a model 53 plow in every section in Iowa, and several in most! In his part of Wyoming, machinery is harder to come by! I've got multiple good snap-coupler plows I'd sell too but RTW and probably others are much closer.
|
|
AC7060IL
Orange Level Joined: 19 Aug 2012 Location: central IL Points: 3335 |
Post Options
Thanks(0)
|
Does it’s 3 pt have adjustable height draft arms?? |
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I appreciate all of the suggestions, and just need to find the time to try them all out. I need to set the hyd pump up for traction booster and try some different top link settings. I do have adjustable lift arms. I had sent some pics on a different thread, and I just need to teach myself how to do it again.
Does any one have a picture of the slipper, that sounds pretty easy to fabricate and install. I'm afraid of the freight cost to purchase a snap coupler plow and have it shipped to WY. What does a good plow go for? Thanks again for all the suggestions. JL |
|
Les Kerf
Orange Level Joined: 08 May 2020 Location: Idaho Points: 759 |
Post Options
Thanks(0)
|
My experience is FAR less than virtually everyone on this forum but my Father-in-law's WD with the Snap Coupler 2-14's in our hard soil was about all it wanted.
|
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I think I made some progress today. When I rechecked my hyd. pump linkage, I left the plow attached. I set the hyd system for traction boost mode. The plow didn't try and sink to the center of the earth, in fact I could only get it to go in the ground 2 or 3 inches, then the traction booster would raise it up, and then back into the ground again, but constantly going up and down. My quadrant lever was as far down as possible. I lengthened the 3 point arms, but didn't make much difference. I feel good that the TB seems to be trying to work, but not sure I'm getting all of the finesse in the adjusting procedure. I brought everything back in the shop and removed the plow and went through the linkage adjustments once again, but it just didn't seem quiet right. Put the plow on,and it acted the same way, just constantly going up and down,but only into the ground a couple of inches.
I know it's asking alot, but I think it would be very helpful for me if someone that's familiar with this system would get on a video call with me, and walk through the adjustments with me. Any thoughts? Thanks, JL |
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20398 |
Post Options
Thanks(0)
|
The large coil spring that surrounds the PTO shaft may have some shims that can be removed to make the spring stiffer to keep the plow from hunting like it is. Loosen the two 1/2" bolts to remove the shims and retighten the bolts afterwards. ***** There could also be an engineering problem using a 3 point hitch versus the regular snap-coupler hitch. When the lift arms raise one inch, the 3-point hitch draft arms raise MORE than one inch, which lifts the plow more than a snap-coupler plow would be lifted. A-C engineered the Traction Booster system around their lift arm length and snap-coupler plow dimensions. It may never work right as a 3-point hitch system.
Edited by DrAllis - 17 May 2024 at 8:10pm |
|
J. Larsen
Bronze Level Joined: 01 Dec 2023 Location: Lander, WY Points: 47 |
Post Options
Thanks(0)
|
I'm following exactly what you are saying about the drawbar spring. I had those bolts out today, but i understood the book stated that there should be 3/16" of free play on the spring. That's an easy item to try.
Thanks, JL |
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |