This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Pulling Forum
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Pistons
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Ol case mike View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 24 Dec 2022
Location: Michigan
Points: 12 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ol case mike Quote  Post ReplyReply Direct Link To This Post Topic: Pistons
    Posted: 23 Apr 2024 at 1:21pm
Is there enough room to install wd 4-1/8 power crater pistons onto a gleaner z these are not wd45 power crater pistons I know sp46 need to be machined some to clear I was just wondering about the power craters
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20523 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 23 Apr 2024 at 2:06pm
M & W piston kit SP-46 fits the 4 inch stroke WC/WD engines and have a Power Crater type bowl in them. If you install them in a WD45 or D-17 engine with the 4 1/2" stroke you need to machine .170" off the top so they don't smack the cylinder head. As far as what you're wanting to use, I have no idea what the compression distance/height is. Might work. Might not.
Back to Top
Ol case mike View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 24 Dec 2022
Location: Michigan
Points: 12 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ol case mike Quote  Post ReplyReply Direct Link To This Post Posted: 23 Apr 2024 at 3:41pm
I have both sets MW 4-1/8
And the smooth bowl I thought them was called power crater that is also 4-1/8 set I was thinking about putting the smooth bowl into a gleaner z code I don’t know either pin height both are still in motors with wd cranks I was just wondering if the smooth bore needed any machine work to be installed like the sp46 piston needs it’s for a unstyled wc pulling tractor that has a stock z gleaner
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20523 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 24 Apr 2024 at 12:15pm
In the "KNOWLEDGE" section of this website, down near the bottom of page 1, you will find "Compression ratio calculator for 226 engines".....good info for you.
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3542 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 24 Apr 2024 at 10:24pm
got ross duplicating some sp46 pistons  (should be done any day now )for me as we speak thanks to steve fischer getting me a piston they are going in my d17 series 4 engine
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3542 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 24 Apr 2024 at 10:26pm
they will be a two ring piston and lighten alittle bit 
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20523 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 25 Apr 2024 at 6:33am
And .170" shorter ??
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3542 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 25 Apr 2024 at 8:39am
no i decided to leave them the same pin to top hieght, and mill them at the machine shop    
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.080 seconds.


Help Support the
Unofficial Allis Forum