This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Allis Chalmers D17 with a new idea 506 loader |
Post Reply |
Author | |
MichaelT
Bronze Level Joined: 30 Oct 2023 Location: Missouri Points: 9 |
Post Options
Thanks(0)
Posted: 4 hours 29 minutes ago at 1:58pm |
I have a New Idea 506 loader and it needs a new hydraylic control valve
The valve on there now may be the original valve and there are no model numbers I would like to install a after market two spool valve but l dont know what to order Northern tool is very close to my home and they have a number of valves shown on their website Any help would be appreciated |
|
Sponsored Links | |
Ray54
Orange Level Access Joined: 22 Nov 2009 Location: Paso Robles, Ca Points: 4474 |
Post Options
Thanks(0)
|
What is the machine doing to make you think the control valve is worn out? I have a lot of old to very old equipment. I have thought the valves were bad on my junk, but 90% of the time it ends up the seals on the piston in the hydraulic cylinder are the problem. They are cheap in most time in comparison to a valve.
If you really need a valve you need the gallons per minute of the pump you have and how much pressure it is able to make. Then a valve able to handle your GPM and PSI, or more and all is good.
|
|
DiyDave
Orange Level Access Joined: 11 Sep 2009 Location: Gambrills, MD Points: 51378 |
Post Options
Thanks(0)
|
Look up your tractor's specs on the internet, or in your manual. You need to know the series of your d-17. Once you have the flow (GPM) and pressure, (PSI), go to surplus center.com, and look for valves...
|
|
Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need!
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20204 |
Post Options
Thanks(0)
|
Any "live" hydraulic pump on any D-17 shouldn't exceed 12 GPM at full throttle. Pressures wouldn't exceed 2400 psi either. We are talking about a 2-way "all hydraulic" loader with tilt cylinders on the bucket, right ??
|
|
MichaelT
Bronze Level Joined: 30 Oct 2023 Location: Missouri Points: 9 |
Post Options
Thanks(0)
|
so it is a D17 series 4
The tubes bucket are not leaking One tube on the lift are is leaking just a bit but the lift works just fine for now The bucket will curl up and then steadyly fall back down and if l lift the bucket about waist high and sit on it it will collapse |
|
MichaelT
Bronze Level Joined: 30 Oct 2023 Location: Missouri Points: 9 |
Post Options
Thanks(0)
|
That is correct, the tubes on the bucket curl are not leaking
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20204 |
Post Options
Thanks(0)
|
It would be foolish to replace the factory OEM valve stack with some aftermarket/cobbled up hydraulic valve. If you can (and you may not be able to) swap the bucket hoses over to the other set of couplers. Or, you could roll the bucket clear back and just unplug the hoses to the bucket while rolled back. Bucket still settles??? it's not the valve. Reseal the bucket cylinders. They are leaking INTERNALLY, not externally.
Edited by DrAllis - 1 hour 2 minutes ago at 5:25pm |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |