| Author |
 Topic Search  Topic Options
|
elbyCJett 
Bronze Level
Joined: 18 Apr 2013
Location: Kentucky
Points: 105
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Wheel Wrenches needed
Posted: 07 Nov 2020 at 1:15pm |
|
I have three tractors (2 CA's and a 160) with spinout or power adjust rear wheels. I do not have the special wrench that is used to unlock the excentrics on them. Does anyone have the wrench. The excentrics have a 13 mm square head.
|
|
D-14, 160, 2 - CAs, 2 - Bs, 2 Gs Roto-Baler, 82S Mower, Rake,444 baler, Kentucky
|
 |
|
Sponsored Links
|
|
|
TomC
Orange Level Access
Joined: 24 Nov 2017
Location: Hillsboro, MO
Points: 1549
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2020 at 1:43pm |
|
Use two 3/4 inch sockets, smaller one inside the other weld them together, works like a charm
|
|
RMD
Silver Level
Joined: 07 Oct 2009
Location: Connecticut
Points: 300
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2020 at 3:52pm |
|
I use a Craftsman 1/2 inch 8-point socket (1/2 inch drive, usually need a cheater bar on the socket handle).
|
|
john(MI)
Orange Level
Joined: 12 Sep 2009
Location: SE MI
Points: 9262
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2020 at 6:45pm |
|
I just used a regular socket. I don't remember what size, but it fit just fine and did the job.
|
|
D14, D17, 5020, 612H, CASE 446
|
|
Gary
Orange Level Access
Joined: 13 Sep 2009
Location: Peterborough,On
Points: 5445
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2020 at 5:28am |
|
A new CA from the factory had 3 eccentrics and one fixed bracket on each rear wheel.
The eccentrics had a 1/2" square protruding head.
A 1/2" drive extension will fit.
Be carefull if the eccentrics are seized, the head will twist off fairly easily
G
|
|
TomC
Orange Level Access
Joined: 24 Nov 2017
Location: Hillsboro, MO
Points: 1549
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2020 at 7:10am |
|
If one of y'all sends me their phone number ( I can't figure out how to post pictures) I'll send you a picture of the two sockets welded for the eccentrics. I'll recheck it to be sure its 3/4 or 1/2 .
|
|
TomC
Orange Level Access
Joined: 24 Nov 2017
Location: Hillsboro, MO
Points: 1549
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2020 at 7:21am |
|
I guess this would help,314-791-0276
|
|
mruhlig77
Orange Level
Joined: 19 Aug 2014
Location: central Indiana
Points: 580
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2020 at 10:36am |
|
weld two together back to back as above...or just tape two together..
|
|
RMD
Silver Level
Joined: 07 Oct 2009
Location: Connecticut
Points: 300
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2020 at 3:32pm |
|
There are two types of heads on the eccentrics. The CA/D10/D12 where usually 1/2 inch square while the WD was generally a 3/4 inch hex head. I think the two types are interchangeable.
|
|
TomC
Orange Level Access
Joined: 24 Nov 2017
Location: Hillsboro, MO
Points: 1549
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2020 at 6:44pm |
|
Weld them together ,I took one smaller socket and put it inside a larger one then welded them together with the 1/2 inch female end out on both,put one on the eccentric and use a breaker bar on the other,
|
|
Dave (NE)
Orange Level
Joined: 12 Sep 2009
Location: Eagle Nebraska
Points: 2148
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Nov 2020 at 8:31am |
|
I believe the 160 is a metric size, however I have been able to use a 1/2" eight point socket on mine.
|
|
Do not argue with an idiot. He will drag you down to his level and beat you with experience. Mark Twain.
|
|
HD6GTOM
Orange Level
Joined: 30 Nov 2009
Location: MADISON CO IA
Points: 6627
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Nov 2020 at 9:18pm |
|
I had an impact socket to fit those I kept on my tire service truck. But I am getting old and cannot remember where I got it. Probably from one of several wholesale places that sell just to tire shops.
|
|
