WD V8 with auto trans

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I bought a parts WD Allis for the engine, I have always wanted to put a v8 in a tractor even just for parades if I don't pull with it. I have a neighbors who's farm had 440 powered WD in the 70s with an auto trans between the 440 and the WD trans. My question is what is the best way to connect the transmission output yoke to the tractor trans input shaft? 

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
ajossund Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 02 Nov 2013 Location: perley mn Points: 36	Post Options Post Reply Quote ajossund Report Post Thanks(0) Quote Reply Topic: WD V8 with auto trans Posted: 12 Sep 2014 at 9:01pm
	I bought a parts WD Allis for the engine, I have always wanted to put a v8 in a tractor even just for parades if I don't pull with it. I have a neighbors who's farm had 440 powered WD in the 70s with an auto trans between the 440 and the WD trans. My question is what is the best way to connect the transmission output yoke to the tractor trans input shaft?

Sponsored Links

MATPA47 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 16 Feb 2015 Location: Marengo ohio Points: 12	Post Options Post Reply Quote MATPA47 Report Post Thanks(0) Quote Reply Posted: 26 Feb 2015 at 9:03pm
	You would want a 2 wheel drive auto so that you have the joke from that, then find a yoke to fit the wd input shaft, then have a driveshaft shop make you a driveshaft. I've thought about doing the same thing to a wc but a wd would be best

Steve in NJ Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Location: Andover, NJ Points: 11820	Post Options Post Reply Quote Steve in NJ Report Post Thanks(0) Quote Reply Posted: 27 Feb 2015 at 9:56pm
	You can pretty much install any engine you want in a set of WD rails. You just need to do the engineering end of it first in order for the job to come out nice n' clean. I have a styled WC which I'm switching over to an unstyled, and I have a GM Marine 3.0L 4 cylinder with standard shift three speed I plan on sliding in the frame rails. It'll still be a 4 cylinder, but how many WC's do ya see with a boat engine?.The plan to couple the drivetrain with the rearend is a custom driveshaft... Another one of my many projects I have goin' on... LOL! Steve@B&B
	39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife

PaulB Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4753	Post Options Post Reply Quote PaulB Report Post Thanks(0) Quote Reply Posted: 28 Feb 2015 at 6:21am
	Back in the day (60s & early 70s) most everyone was building a cheap puller with a worn out tractor and a junkyard engine. As mentioned set everything in place the so the driveshaft lines up then have a short driveshaft made with a joint on each end to fit. If length is a concern, you can have the yoke from the auto trans and the piece from the tractor trans machined off and weld a chain sprocket on each then use double roller chain for the coupling. For light duty #50 could work I have always used #60 and even behind a injected & blown 440 the chain never wore out. Would you be interested in a built up Dodge 360? If so send a PM for all the details.