Farm Equipment - OK wisconsin engin guys

Print Page | Close Window

OK wisconsin engin guys

Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=6848
Printed Date: 16 Jan 2025 at 2:06pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com

Topic: OK wisconsin engin guys

Posted By: Vinnie/S.D.
Subject: OK wisconsin engin guys
Date Posted: 19 Jan 2010 at 8:26pm

I want to over haul my VH4D bobcat 600 engin (need to replace the heads) will any 30hp heads work on this engin I will call any one that will give me your noumber or email mine is 605 338 0006 or mailto:vmdonelan@msn.com - vmdonelan@msn.com Thanks vince

Replies:

Posted By: Don(MO)
Date Posted: 20 Jan 2010 at 8:13am

I think I have a vhd head or two off a M-600 Bobcat, Just give me a call tonight at home.

816-697-1995 after 6PM. I live East of KC MO. about 20 miles.

No they need to be off a VHD to work right.

Don

-------------
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.

Posted By: TramwayGuy
Date Posted: 20 Jan 2010 at 9:43am

What is wrong with your heads? If it is just the spark plug holes, they can be repaired.

There were standard heads and there were high altitude/LP-gas heads as well.

Make sure the replacement heads have the same casting number.

Posted By: Matt (Jordan,MN)
Date Posted: 20 Jan 2010 at 10:45am

You should be able to get new heads from wisconsin or you Bobcat dealer. The Bobcat dealer that i worked at had a set on hand. I even replaed a few that cracked.

Posted By: R Aiken
Date Posted: 20 Jan 2010 at 12:38pm

I have a few VH4D engines for parts, should have some good heads.

Posted By: Clay
Date Posted: 20 Jan 2010 at 12:53pm

What is a fair price to pay for a good VE-4?

Posted By: Don(MO)
Date Posted: 20 Jan 2010 at 5:32pm

Clay, Is your VE-4D off a hay baler?

-------------
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.

Posted By: Clay
Date Posted: 21 Jan 2010 at 4:23am

Not sure what the engine was on before I bought it.

I use it to power a 20 G.P.M. pump on my log splitter. Wish I had one with electric start.

Posted By: R Aiken
Date Posted: 21 Jan 2010 at 5:30am

Clay. I think I enough parts to put electric start on your engine. Richard

Posted By: Clay
Date Posted: 21 Jan 2010 at 11:01pm

I know the fly wheel has to be changed.

My engine has a magneto. I believe the elecrtic start engines have a distributor.

The engine I have was making some noise. I think it could be a bearing. It was hitting on all four cylinders. Guess I will have to tear into it and find out.

Posted By: JC-WI
Date Posted: 21 Jan 2010 at 11:16pm

Someday I will have to get into my Wis engine too that is on a Bobcat. kinda tired and has piston pin noise (I hope thats it) or bad rod bearing. had cracked aluminum heads and changed them out to cast iron heads.

Seems to run alright that way, but think the cast iron ones are a bit less compression.

I will also need a drive pully flange since the one I have has a chunk missing on outer edge.