Pulling Forum - d 19 -190 hi low

Print Page | Close Window

d 19 -190 hi low

Printed From: Unofficial Allis
Category: Other Topics
Forum Name: Pulling Forum
Forum Description: Forum dedicated to Tractor and Garden Pulling
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=66681
Printed Date: 23 Nov 2024 at 12:38pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com

Topic: d 19 -190 hi low

Posted By: bradley6874
Subject: d 19 -190 hi low
Date Posted: 10 Mar 2013 at 8:32pm

Ok if a 190 is just a newer version of a d19 which hi low is stronger for pulling the manuel from a d19 or hydrolic from a 190 just thinking out loud

-------------
You can wash the dirt off the body but you can’t wash the farmer out of the heart and soul

Replies:

Posted By: DrAllis
Date Posted: 10 Mar 2013 at 8:34pm

Hydraulic version will old much more HP and it even has it's limits.

Posted By: bradley6874
Date Posted: 10 Mar 2013 at 8:36pm

Thanks dr glad you were listning

-------------
You can wash the dirt off the body but you can’t wash the farmer out of the heart and soul

Posted By: bradley6874
Date Posted: 20 Mar 2013 at 11:46am

Ok another question on a 190 valve at 400 psi how much flow do you need and does the 3rd line return from the valve back to the base or direct it some where else thanks

-------------
You can wash the dirt off the body but you can’t wash the farmer out of the heart and soul

Posted By: bradley6874
Date Posted: 22 Mar 2013 at 3:05pm

Anybody got any sugestions

-------------
You can wash the dirt off the body but you can’t wash the farmer out of the heart and soul

Posted By: DrAllis
Date Posted: 22 Mar 2013 at 6:39pm

The hydraulic pump delivers between 5 and 6 GPM to the steering orbitrol motor connected to the steering wheel. When the steering circuit is done with the 5 to 6 GPM delivered to it, the same 5 to 6 GPM of hyd oil is sent downstream to the Power Director valve and the back pressure to the orbitrol motor is modulated to between 250 and 350 psi. Whenever you are in LOW or HIGH range, this 250 to 350 psi oil is directed to either the front tube or rear tube to apply that selected clutch. If it takes 2 GPM to apply the selected clutch, then the remaining 3 to 4 GPM goes thru the center tube for lubrication of the intermediate gears, bearings and the Power Director clutch discs themselves, and then of course has been returned to the sump. The gallons of "lube circuit" oil is dependent upon how much leakage each clutch pack has and how many GPM's were delivered from the pump to begin with. The priority is that each clutch is delivered enough volume of pressurized oil to lock up the clutch so it won't slip under load. So, I guess the answer is, you need 5 GPM minimum because that's what the specs are. I don't quite understand what you're trying to do, but I will advise you that the PD clutch has it's HP/torque limits and there is only so much you can do to it to hold increased HP.....300 HP isn't a problem....500 HP starts to be, depending on tires and weight class, etc.

Posted By: MACK
Date Posted: 22 Mar 2013 at 9:21pm

Don't turn the PD over 3000 RPMs unless you want your legs torn off. MACK

Posted By: bradley6874
Date Posted: 23 Mar 2013 at 12:01am

Thanks mack i have elimanated all hydrolic and am installing a small pump for just the power director wasnt figuring but about 3000 rpms for this season gona get the bugs out then build a new motor and then the power director will have to go but think i might need it with the small motor again thanks

-------------
You can wash the dirt off the body but you can’t wash the farmer out of the heart and soul

Posted By: bradley6874
Date Posted: 23 Mar 2013 at 12:02am

Sorry and thanks dr

-------------
You can wash the dirt off the body but you can’t wash the farmer out of the heart and soul