WD compression
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=48263
Printed Date: 27 Aug 2025 at 12:20pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: WD compression
Posted By: Bill_MN
Subject: WD compression
Date Posted: 31 Mar 2012 at 4:47pm
|
what was the compression ratio and psi of a bone stock WD engine when brand new? going to do some maintenance on mine and want to get a read on how worn it is. at what compression would you guys consider a rebuild? oil pressure is still very good
------------- 1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow |
Replies:
Posted By: Longmeadow Farm
Date Posted: 31 Mar 2012 at 4:58pm
|
WD specifications for gasoline version only 5.75 to 1 compression ratio 110 PSI WD low octane fuel 4.5 to 1 80 pSI
|
Posted By: TedBuiskerN.IL.
Date Posted: 31 Mar 2012 at 8:40pm
|
I would be more interested in the balance between cylinders than compression pressure. If all cylinders are the same or close to the same, and oil burning is minimal, run it. ------------- Most problems can be solved with the proper application of high explosives. |
Posted By: Brian G. NY
Date Posted: 01 Apr 2012 at 10:35am
|
I'm with Ted; Repair manuals rarely specify an exact compression pressure, but instead, (usually) indicate that there should be no more than a 10% difference between the readings on the highest and lowest cylinders. Having said that, I have my WD-45 manual open before me and it states: Compression Pressure (Gas) 125# @ 500 RPM.
|
Posted By: DrAllis
Date Posted: 01 Apr 2012 at 1:51pm
| I could care less what the number really is, as long as each cylinder is even and the engine doesn't use oil and oil pressure is acceptable. Remember, compression testers are like speedometers....no two may read exactly the same. |
Posted By: Brian G. NY
Date Posted: 01 Apr 2012 at 2:05pm
|
Dr. Allis,
Then, even 10% difference is unacceptable to you?
|
Posted By: B26240
Date Posted: 01 Apr 2012 at 2:18pm
| Im with the DR. on this the compression tester I have requires some skill to hold it in the hole while cranking and have found if I repeate the test I often will get a different reading. I also say that engine should have been running and warmed up befor testing. |
Posted By: Glockhead SWMI
Date Posted: 01 Apr 2012 at 3:47pm
| my wc only has thirty PSI. granted, it doesn't start real well... |
Posted By: Brian G. NY
Date Posted: 01 Apr 2012 at 3:59pm
|
B26240,
The good ones screw into the plug hole and do not leak.
Not to say they may not vary in accuracy!?
|
Posted By: wjohn
Date Posted: 01 Apr 2012 at 4:00pm
I bet it's easy to spin with the hand crank though haha! My WC is significantly tougher to hand crank than my B, so I think it has decent compression. ------------- 1939 B, 1940 B, 1941 WC, 1951 WD, 1952 CA, 1956 WD-45 |
Glockhead SWMI wrote:Posted By: Stan IL&TN
Date Posted: 01 Apr 2012 at 4:03pm
|
My compression tester has adapters that screw into the head with an o-ring seal and I find that they are very reproducable but I will agree that there would be some variance between guages. ------------- 1957 WD45 dad's first AC 1968 one-seventy 1956 F40 Ferguson |
Posted By: JimD
Date Posted: 01 Apr 2012 at 4:14pm
|
I guess I got lucky with mine. I seem to get very reproducable results. Maybe 5 or so psi different. But then testing the same hole over and over is still not going to get perfect results due to oiling, heat, and speed at which the starter spins. I usually recommend a rebuild around 90psi if the customer isn't happy with power. 125 seems to be a good target number, but I've had 125cu in engines go as high as 150, but I also didn't know what had been done prior to my work. JimD ------------- Owner of http://www.OKtractor.com" rel="nofollow - OKtractor.com PM for an instant response on parts. Open M-F 9-6 Central. We have new and used parts. 877-378-6543 |