D-14 top link bracket dimensions
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=26959
Printed Date: 27 Feb 2025 at 7:59am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: D-14 top link bracket dimensions
Posted By: jaybmiller
Subject: D-14 top link bracket dimensions
Date Posted: 08 Mar 2011 at 1:05pm
|
Hay there. Finally bought a 3 point adapter for my D-14 but the guy kept the top link mounting bracket.Could someone please email me a picture of a real one, and some of the key dimensions?
One picture I have has 3 sets of holes which I know are 3/4"*,maybe 2" gap for top link ?
It also 'wraps around' the front of the read end.
I've got a couple CNC guys that owe me favours....time to cash in !
Any help is appreciated!
Wife's looking forward to the 5' rototiller, kinda offsets the G and Gleaner episodes....
------------- 3 D-14s,A-C forklift, B-112 Kubota BX23S lil' TOOT( The Other Orange Tractor) Never burn your bridges, unless you can walk on water |
Replies:
Posted By: Tracy Martin TN
Date Posted: 08 Mar 2011 at 6:44pm
| Jay, Stiener or Heitman has them. I think I saw them earlier. I was going to make some, but they are already less than I could do them for.Putting those two front holes at that bend is tough. HTH Tracy Martin |
Posted By: jaybmiller
Date Posted: 08 Mar 2011 at 7:44pm
|
Hay Tracy
Just got a Steiner cat today....didn't see any top link brackets...might have missed them ...Who is Heitman ?
PS. If I could part out my G for what Steiner wnats I'd be rich !!!
------------- 3 D-14s,A-C forklift, B-112 Kubota BX23S lil' TOOT( The Other Orange Tractor) Never burn your bridges, unless you can walk on water |
Posted By: JoeO(CMO)
Date Posted: 08 Mar 2011 at 8:35pm
|
I have one, will dig after it tomorrow ------------- |
Posted By: JoeO(CMO)
Date Posted: 10 Mar 2011 at 7:42pm
Jay;
  I took some measurements of the top link bracket I have and they are as follows;
Top Plate thickness=5/16
Two plates with holes=1/2 x 2-1/4 x 4-1/2
Plate spread=1-3/4
Holes=7/8 dia
Holes= 3/4 from rear side of plate
Holes=1-1/2 spacing
Holes, top hole=1-1/2 down from top of plate(horizontal surface)
I'll have to get the radius of top and bottom of plate.
If you cut some of these, I could use a pair, as I also have a top link bracket with single hole(D14 & D15 I) that could use an update.
HTH
------------- |
Posted By: Tracy Martin TN
Date Posted: 10 Mar 2011 at 7:48pm
| I thought I had seen where these were being reproduced. Really thought they were in the OAN magazine. If not I would make some if there was enough interest in them. Toughest part is the front bend and holes. HTH Tracy Martin |
Posted By: GregLawlerMinn
Date Posted: 11 Mar 2011 at 7:36am
|
If looking to purchase, contact Tony Carbough and/or Jim D (OK Tractor). They both have the brackets that fit very nicely.
Link to Tony's site: http://www.tonystractors.com/ - http://www.tonystractors.com/
Link to OK Tractor site: https://secure79.elinuxservers.com/~tractor/catalog/index.php/cPath/47?osCsid=3dc969f59c6d6a30e8878ce655b2cabb - https://secure79.elinuxservers.com/~tractor/catalog/index.php/cPath/47?osCsid=3dc969f59c6d6a30e8878ce655b2cabb
Both are very helpful and great folks to do business with.
------------- What this country needs is more unemployed politicians-and lawyers. Currently have: 1 D14 and a D15S2. With new owners: 2Bs,9CAs,1WD,2 D12s,5D14s,3D15S2s, 2D17SIVs,D17D,1D19D;1 Unstyled WC |