Farm Equipment - 210-220 drawbar

Print Page | Close Window

210-220 drawbar

Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=25296
Printed Date: 25 Feb 2025 at 6:12am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com

Topic: 210-220 drawbar

Posted By: Riggs/Ia
Subject: 210-220 drawbar
Date Posted: 05 Feb 2011 at 8:50pm

was wondering if anybody has a straight drawbar for a D21,210,or a 220. Needs tobe straight!!! Thanks in advance

Replies:

Posted By: injpumpEd
Date Posted: 06 Feb 2011 at 9:58am

I have one in IL pm me if interested. Ed. Straight ones are from 7000 series.

-------------
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!

Posted By: riggs
Date Posted: 06 Feb 2011 at 1:22pm

am looking for a 220 drawbar. the straight ones wont work. i was referring to the bar. its going on a tractor i am restoring and and i dont want one thats twisted, welded or bent. e-mail me @ mailto:acfamily@mchsi.com - acfamily@mchsi.com . thanks

Posted By: cdreb
Date Posted: 07 Feb 2011 at 2:30pm

I GOT MINE FROM ROCK VALLEY IA, THEY ARE TO SHIP 2/7/11

Posted By: Brad Cober
Date Posted: 07 Feb 2011 at 5:56pm

Will a straight draw bar from a 7000 fit nicely on a 220?. Run it straight through on top of the block?

Mine is bent and hangs way to low.

Posted By: Amos
Date Posted: 07 Feb 2011 at 6:36pm

Brad

Not sure if a 7000 will fit. I had a straight one made and ran it on top of the bar that supported the crooked one. If my memory is right I had to put the bar on top of the supports and not underneath as it had been for the crooked bar (original). Mine was bent down a full 4 inches from where it should have been. A straight bar was the best thing I did to the 210, the implements sit up a lot better, especially the corn planter.

Posted By: Brad Cober
Date Posted: 07 Feb 2011 at 6:40pm

That is what I would like to do. Run a straight bar on top of the support. It sure does make a difference with an implement hooked up that isnt dragging on the ground.

Brad

Posted By: injpumpEd
Date Posted: 07 Feb 2011 at 7:07pm

yes a 7060 strait drawbar works nice on a 210/220. It is way longer than you'll need, so you can drill a new hole for front pin. Take the rear cross support from the bottom, and put it on top of the tabs, then make spacers to put top plate back on and still allow swing.

-------------
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!

Posted By: riggs
Date Posted: 08 Feb 2011 at 3:19pm

ed, do you have a number i can reach you at?

Posted By: injpumpEd
Date Posted: 08 Feb 2011 at 6:31pm

send me a pm, I'll give you a number. Email works also, ed64drag@lycos.com

-------------
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!

Posted By: Jordan(OH)
Date Posted: 09 Feb 2011 at 1:24pm

D21 will be too short for 220