Allis part ID?
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=24869
Printed Date: 25 Feb 2025 at 9:45am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Allis part ID?
Posted By: Murph-NC
Subject: Allis part ID?
Date Posted: 29 Jan 2011 at 3:55pm
|
Cleaned up at the family farm some today. I feel pretty confident that these three orange pieces are AC. But the pitman straps I'm not so sure about... they look a little different than the ones on our B/C or #3 mowers. Any ideas on any of these pieces? Thanks in advance.   ------------- '41 C w/Woods L503 mower, #3 mower, 2-way plows for C |
Replies:
Posted By: morton(pa)
Date Posted: 29 Jan 2011 at 4:05pm
|
The rusted part with the tape measure in the bottom picture is whats left of a Pitman arm for a sickle bar mower for sure. Can't tell off the top of my head if it's for a B/C mower. The mower is an hour and 45 mins away, otherwise I'd just go check! Sorry. Also can't find my PDF Version of the Sickle Bar Mower manual..I guess I never got another one after my computer crashed...any chance anyone has one?
|
Posted By: Murph-NC
Date Posted: 30 Jan 2011 at 7:22pm
|
Thanks Morton. Anybody else have ideas on any of these? ------------- '41 C w/Woods L503 mower, #3 mower, 2-way plows for C |
Posted By: Murph-NC
Date Posted: 02 Feb 2011 at 7:43pm
|
bump ------------- '41 C w/Woods L503 mower, #3 mower, 2-way plows for C |
Posted By: KenBWisc
Date Posted: 03 Feb 2011 at 8:13am
|
The pitman strap is the same one I have on a sickle mower on my G. Think that would be a #2?
------------- '34 WC #629, '49 G, '49 B, '49 WD, '62 D-19, '38 All Crop 60 and still hunting! |
Posted By: pumpkin man
Date Posted: 03 Feb 2011 at 4:49pm
| I have two { B } mowers both 6 ft. both difft. one has the up dated [reinforced ] arm from the frame to the knife head the other one is not. that one uses the pitman straps that you show. the other has the sliding spring lock. both work fine |
Posted By: Murph-NC
Date Posted: 11 Feb 2011 at 9:17pm
|
Thanks guys. Dad thinks the two matching pieces with the welded studs might have been for the rear tool bar for the B cultivator setup. Anybody have a PDF of the manual I could bum to verify? Or does anyone know? Grandpa only had so many AC items, so we don't have too many others to choose from. ------------- '41 C w/Woods L503 mower, #3 mower, 2-way plows for C |
Posted By: GlenninPA
Date Posted: 12 Feb 2011 at 7:13am
| The B did not have a "rear" toolbar for the 60 series cultivator, but the C did for the 80 series. The B rear cutlivator (field cultivator) does not have any parts resembling that, unless it were something to bolt to the rockshaft, but I believe that piece has a half moon cutout on it. |
Posted By: JoeO(CMO)
Date Posted: 12 Feb 2011 at 7:26am
|
I don't think the pitman end is AC, just doesn't look right. The stop was screwed in on an AC.
The better looking part looks like a 25' "Stanley" tape. lol. Well, people do it to me. Couldn't resist. ------------- |
Posted By: Bob-Maine
Date Posted: 12 Feb 2011 at 8:22am
|
Joe, Now I don't feel so bad when i post something like your's. :>/
Bob@allisdowneast ------------- I used to think I was indecisive, but now I'm not sure. |