Need Allis G Double Tool Bar Dimensions
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=23918
Printed Date: 23 Feb 2025 at 6:32pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Need Allis G Double Tool Bar Dimensions
Posted By: oldironguy
Subject: Need Allis G Double Tool Bar Dimensions
Date Posted: 11 Jan 2011 at 10:19pm
Hey guys. I have some Planet Jr wheels, cultivator shanks, clamps and shoes and want to build a double tool bar for my Allis G. I need dimensiions to accurately recreate one. I've shown the didmenstions on the enclosed image. Could anyone who has one measure it and send me the dimensions I've marked?
 |
Replies:
Posted By: Scott(GA)
Date Posted: 12 Jan 2011 at 6:02am
|
I will get these measurements for you when I get home from a business trip.
I should have gotten back this morning but it's been pushed back about 24 hours.
Scott
|
Posted By: oldironguy
Date Posted: 12 Jan 2011 at 8:52am
|
Thanks Scott.
That's terrific.
Dick
|
Posted By: Scott(GA)
Date Posted: 14 Jan 2011 at 12:38pm
|
Dick,
I have 3 of these double-bar cultivators at my home near Atlanta, GA and a 4th at my dad's farm in Indiana. I am not able to examine the Indiana cultivator at this time.
I remember dad talking about "Willie Ecker" cultivators - Willie was a local welder that apparently built these double-bar for farmers in the neighborhood.
In looking at the 3 cultivators that I have access to here in Georgia, I think one is a Willie Ecker model, one may be home-made or maybe not and the third one appears to be an Allis-Chalmers model.
The only reason I think the 3rd one is "stock" is due to the fact that it matches the drawing in the manual exactly. The one that I stated was "home-made or maybe not" matched pretty closely but it only has 2 drilled holes (not 5) to receive each of the mounting bracket legs.
I will use the cultivator that appears to be stock Allis-Chalmers for the dimensions that I'm going to list.
I'll post the dimensions for the mounting brackets in the next post.
A= 1 1/2"
B= 3/4"
C= 12 3/4"
D= 63"
E= 28 1/4"
F= 25"
G= 9"
H= 2"
I= 2"
J=2"
K=1"
Notes:
E is measured to the opposite side of the angled brace's width - weld might have influenced the measurement (everything else is pretty much round measurements) but 28 1/4" is what it looked like to me.
F is measured to the closest side of the angled brace's width.
G, H, I, J & K are all measured from the end of the bar-stock to the center line of the hole.
The drilled holes take a 3/8" bolt easily but not a sloppy fit.
It appears that the "C dimension" pieces are set in about 1/4" from the end of the "D dimension" pieces. Distance from one "C dimension" piece to the opposite end "C dimension" piece is 62 1/2".
Scott
|
Posted By: GlenninPA
Date Posted: 14 Jan 2011 at 1:10pm
| I sure am glad you are getting good use out of that book, show us some photos when you get the unit built ! |
Posted By: Scott(GA)
Date Posted: 14 Jan 2011 at 1:11pm
|
Dick,
I am uncomfortable with the accuracy of most of my measurements on the mounting brackets. Measurement "N" being the exception: N= 6 1/2" and is 3/4" x 2"
What I'd like to do is take the brackets off the cultivator, trace the bracket on a piece of paper and mail it to you.
Send me a private message with your address and that's what I'll do.
Best regards,
Scott
|
Posted By: Scott(GA)
Date Posted: 14 Jan 2011 at 1:20pm
|
One more thing about the mounting brackets. The "bent" part of the assembly is the same bar-stock as the rest of the cultivator - 3/4" x 1 1/2".
The part that is defined by the "N" dimension is different bar-stock - 3/4" x 2".
Best regards,
Scott
|
Posted By: Scott(GA)
Date Posted: 14 Jan 2011 at 9:22pm
|
Dick,
Got the tracing done and will get it in the mail tomorrow.
When I took off the Attaching Arch Assembly, I found 2 bushings in it. I just pulled out my Parts Catalog for Model G implements and, sure enough, bushings are mentioned.
I think that confirms that this really is an Allis-Chalmers Double Tool Bar.
I measured the holes as best as I could and it looks to me like they are 5/8" and then the bushing was inserted.
The forward hole is centered 1 1/8" from the end.
The rear hole is centered 11/16" from the end.
Note:
The ends of the arch assembly are not "neatly" cut. As a result, the measurement from the end to centerline of the hole was difficult to determine with complete confidence. The above measurements are as close as I could determine.
Best regards,
Scott
|
Posted By: Warren(Oh)
Date Posted: 15 Jan 2011 at 4:57am
| I may have to try my hand at making one of these someday ! I have a single tool bar, might just make an add on for it ! |
Posted By: Scott(GA)
Date Posted: 15 Jan 2011 at 7:57am
|
Dick,
An additional note regarding the drilled holes in the cultivator "frame" (G,H,I,J,K)...
Regarding these holes I had written the following note:
G, H, I, J & K are all measured from the end of the bar-stock to the center line of the hole.
The drilled holes take a 3/8" bolt easily but not a sloppy fit.
I was looking at the Implements Parts Catalog this morning and I noticed that the Attaching Arch Assemblies call for 7/16" bolts to attach them to the culltivator "frame". So that defines those holes better than my original note.
Best regards,
Scott |
Posted By: Dusty MI
Date Posted: 15 Jan 2011 at 8:53am
|
I believe that that most pieces when manufactured are cut by shearing and holes are punched, which is why they are a little hard to get a good measurement. Dusty ------------- 917 H, '48 G, '65 D-10 series III "Allis Express" |
Posted By: contrary_farmer
Date Posted: 18 Jan 2011 at 6:24am
|
Here's one for sale on ebay. Must be solid gold!
http://cgi.ebay.com/Allis-Chalmers-G-cultivator-vegetable-toolbar-3-rows-/120673287623?pt=LH_DefaultDomain_0&hash=item1c18b03dc7 - http://cgi.ebay.com/Allis-Chalmers-G-cultivator-vegetable-toolbar-3-rows-/120673287623?pt=LH_DefaultDomain_0&hash=item1c18b03dc7
 |
Posted By: Scott(GA)
Date Posted: 18 Jan 2011 at 9:26am
|
I've looked closely at the pictures and I can't see the "open-V cross-brace" (my terminology) that should be there.
Best regards,
Scott
|
Posted By: Warren(Oh)
Date Posted: 18 Jan 2011 at 6:14pm
| That person has several pieces for the double tool bar on ebay AND thinks they're all made of gold !!!! |