Quick Hitch
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=205890
Printed Date: 16 Mar 2025 at 4:50pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Quick Hitch
Posted By: Codger
Subject: Quick Hitch
Date Posted: 16 Mar 2025 at 7:48am
|
I have ordered but not yet received a "Pat's" quick hitch for my tractor. It is a Cat II setup but everything I have is Cat I. I have plenty of bushings and replacements are cheap enough should any become lost, etc. I'm hoping this will make the tractor more useful than already is as I only mow with a 72" RD-7200 Woods finish mower, but have recently purchased a new rototiller, and 60gl Demco three point sprayer. Having the live PTO makes this tractor so much more usable than my older Ford branded Shibaura tractor although I'm keeping it also. I never realized how inconvenient the transmission operated PTO was...... Probably preaching to the choir talking about this so looking at things to watch out for, or make it more useful. Should I consider a hydraulic top link as instance? I have a single hydraulic remote available at the rear that is not detented and snaps back to neutral when the handle is released. I need to check if this remote is only powered one way, or both as never have used it. This remote I plan to use to operate a skid mount winch setup for dragging smaller logs up hills on our property. I may install detents, but in winching applications, this is not always a good thing to do. I don't farm so have no real needs other than the PTO for driving things like the post hole auger, mower deck, sprayer, and now the tiller. Hopefully this hitch setup will ease changing from one implement to another much easier. Just looking for general input from those using this type hitch setup as I have no experience. Thanks, ------------- That's All Folks! |
Replies:
Posted By: jaybmiller
Date Posted: 16 Mar 2025 at 8:01am
|
fyi I'd install (glue ?) the bushings on every implement I bought and bolted a top link onto all my 3PH implements. That way,install and use, no turning the top link a zillion turns every time. keep joints oiled,especially when done and stored for awhile ------------- 3 D-14s,A-C forklift, B-112 Kubota BX23S lil' TOOT( The Other Orange Tractor) Never burn your bridges, unless you can walk on water |
Posted By: Codger
Date Posted: 16 Mar 2025 at 8:30am
|
Thanks, I like to think myself a compentent welder and was planning on affixing the bushings permanent. Doesn't seem I'm out of line there as the pins are readily replaceable should that be needed. Twisting that top link; that was the reason for asking about the hydraulic top link. I know that gets old fast. I have a Cat II tractor end and the Cat I on all the implements of the two top links I have. We must think alike as I purchased the second top link leaving it on the auger for this very reason.
------------- That's All Folks! |
Posted By: PaulB
Date Posted: 16 Mar 2025 at 8:47am
|
Are the lower link connections adjustable for width? The Cat I width is 26" whereas the Cat II width is 31". ------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
Posted By: Codger
Date Posted: 16 Mar 2025 at 8:54am
|
Yes, they are adjustable for width. It has those links for pins to drop in to keep the arms spread. I want to say the ball ends have 1.125" diameter holes in them? ------------- That's All Folks! |
Posted By: truckerfarmer
Date Posted: 16 Mar 2025 at 9:07am
|
Cat II quick hitch more than likely won't work with Cat I implements. It's not just the pin size, it's the spacing between the pins. ------------- Looking at the past to see the future. '53 WD, '53 WD45, WD snap coupler field cultivator, #53 plow,'53 HD5B dozer Duct tape.... Can't fix stupidity. But will muffle the sound of it! |
Posted By: Codger
Date Posted: 16 Mar 2025 at 11:15am
A Pat's hitch is not a weldment as most are. It's a modification to the lower lift arms. ------------- That's All Folks! |
truckerfarmer wrote:Posted By: DrAllis
Date Posted: 16 Mar 2025 at 3:04pm
| I looked up his product. His quick-hitch devices will move your load farther back, which will require your top link to be longer. Hopefully it has enough threads to be able to extend that much more. If not, I might fabricate an extension for each implement you use to solve this issue. The extension could be welded, but I might prefer it is bolted so it could be removed if needed, not making it permanent. Also, depending on the load you are lifting, more tractor front end weight may be needed because your load looks like it will be 4 to 6 inches farther back. |