Plow share bolts
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=202509
Printed Date: 23 Nov 2024 at 12:55pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Plow share bolts
Posted By: AC720Man
Subject: Plow share bolts
Date Posted: 31 Jul 2024 at 9:57am
|
I was fortunate to get 4 new Bullet style plow shares for my 70 series plow that I pull with my 190 XT. Part number stamped on the back is 341396. Takes a funny shaped plow bolt, maybe a 7/16”x2”? I have my dealer trying to find them but was hoping someone here would assist me that will have better knowledge of what the style, size, and best place to purchase them? Let’s face it, most all the knowledgeable AC parts guys at dealers are long gone. But there are a lot a guys on here that know this stuff by memory. Thanks in advance Robbie ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Replies:
Posted By: AC720Man
Date Posted: 31 Jul 2024 at 10:18am
|
11/32” according to my digital caliber so closer to 3/8” measuring across the threads of the old bolt ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: allis1221G
Date Posted: 31 Jul 2024 at 10:38am
| I have a bunch of nos plow bolts. Couple different sizes. I can check for ya if needed. Pic and size of yr bolt would help |
Posted By: PaulB
Date Posted: 31 Jul 2024 at 10:54am
|
Many of the NOS "Bullet-Blade" plow shares I've had had a bolt hole the had a flat relief and a diamond shaped hole under that. Basically a 2 point bolt. I don't think I have any left and they may be hard to find as nothing in generic hardware would use that special bolt. From what I can get looking at the parts book, I think you want to find 341900 which is superseded by 346907, these would be 3/8" bolts. This may or may not be the bolt you're looking for. If you need 7/16" bolts for "stoney" shares that number should be, 348293. ------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
Posted By: AC720Man
Date Posted: 31 Jul 2024 at 11:14am
|
I’m trying to post a picture but the file size is too big. The head of the bolt is slightly bigger than a 1/2”. The shoulder that the bolt rest in is to keep it from turning is oblong. Not sure how else to describe it? ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: AC720Man
Date Posted: 31 Jul 2024 at 11:19am
|
Share number is actually 341396, difficult to read. I updated the initial post as well ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: Kenny L.
Date Posted: 31 Jul 2024 at 1:04pm
|
AC720Man Text me the picture of the bolt I think I've them. FIVE 6 THREE- NINE 20- TWO TWO 7 TWO. If I don't I'll post the picture for you. Kenny L. |
Posted By: BigGuy1000
Date Posted: 31 Jul 2024 at 3:49pm
|
Buy from Shoup, they have several sizes, get the right size! |
Posted By: Tracy Martin TN
Date Posted: 31 Jul 2024 at 4:47pm
|
Most of the later ones were a cat eye shape. HTH Tracy ------------- No greater gift than healthy grandkids! |
Posted By: Dave (Mid-MI)
Date Posted: 31 Jul 2024 at 5:36pm
| I think these are called clipped head bolts. A company called AFT Fasteners has them available in several sizes. |
Posted By: AC720Man
Date Posted: 31 Jul 2024 at 6:11pm
|
Tracy, that’s a good description. ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: Mikez
Date Posted: 31 Jul 2024 at 7:02pm
The 346907. And sorry these are not for sale  |
Posted By: Kenny L.
Date Posted: 31 Jul 2024 at 7:19pm
|
Posted By: Mikez
Date Posted: 31 Jul 2024 at 7:23pm
| 341396 share fits 375 bottom and is 16” economy |
Posted By: AC720Man
Date Posted: 31 Jul 2024 at 7:40pm
|
Thanks for the picture Mike, ugh not for sale....do you know where I can get some? ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: Mikez
Date Posted: 31 Jul 2024 at 7:58pm
|
We have plows too. Would hate to need them some day. Figured the description might help you. I will check a few other places tomorrow
|
Posted By: AC720Man
Date Posted: 31 Jul 2024 at 7:59pm
|
Thanks Kenny posting my picture for me. ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: AC720Man
Date Posted: 31 Jul 2024 at 8:34pm
|
I looked on AFT's website and I'm not seeing a bolt like I need. Will call them tomorrow. Now that I have a AC part number and a picture that is a huge help.
Thanks Mike ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: Lars(wi)
Date Posted: 31 Jul 2024 at 8:51pm
|
I never was around AC plows, mostly IH, the bolts for the shares were ‘reverse thread’. Instead of ‘lefty loosey righty tighty, it’s lefty tighty righty loosey. ------------- I tried to follow the science, but it was not there. I then followed the money, and that’s where I found the science. |
Posted By: Allis dave
Date Posted: 01 Aug 2024 at 7:20am
|
I had an Allis plow wiht those same bolts. I never knew what they were.... New shares I put on had different bolts
|
Posted By: AC720Man
Date Posted: 01 Aug 2024 at 7:25am
|
Bolts were rusted in place from sitting in the dirt for many years. I had no choice but to cut them off. The nuts were rounded off. I bought this plow about 4 years ago and it needed shares at that time. ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: PaulB
Date Posted: 01 Aug 2024 at 10:38am
I guess it wasn't official when I responded with the correct part number. Rob: How many do you need? I had always furnished the bolts when I sold shares. I found I still have a bunch of the 3/8" size available. I also have the 7/16" size available. Is the Page County fair going to have my class (turbo Tractor) at the pull on the 20th?  ------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
PaulB wrote:Posted By: AC720Man
Date Posted: 01 Aug 2024 at 11:26am
|
Paul you did have the correct part number. Once Mike posted a picture of the bolt and the box with the part number it confirmed that. Wasn’t doubting you just wanted visual confirmation of the odd ball bolt so I knew what to look for. Unsure about the classes at the moment but I will be glad to find out for you. I’m not pulling my XT anymore as I refuse to drill and install cross bolts in my factory turbo elbow to satisfy the new rules. Send me a pm with a price on the bolts, I would like to get at least 20 to have some spares. Replacing all 4 shares, 4 bolts per share. ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: AC720Man
Date Posted: 04 Aug 2024 at 10:58am
 Here you go Paul, pulled off the website. ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: AC720Man
Date Posted: 15 Aug 2024 at 11:51am
|
Thanks Paul for selling me the plow bolts. They arrived today and are a perfect fit. Good luck at the pull Saturday. ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: Charlie175
Date Posted: 17 Aug 2024 at 5:36am
|
Rob, the pull info you show was for the Luray Fire Dept pull on May 20th. This is the Page Fair pull info: https://www.pagevalleyfair.org/2024-fair/grandstand-entertainment#grand23%20" rel="nofollow - https://www.pagevalleyfair.org/2024-fair/grandstand-entertainment#grand23
7000 Farm Tractors – N N: Non-Points Class ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |