1953 Model D grader
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Construction and other equipment
Forum Description: everything else with orange (or yellow) paint
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=199289
Printed Date: 19 Dec 2024 at 11:45pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 1953 Model D grader
Posted By: newbe2
Subject: 1953 Model D grader
Date Posted: 16 Jan 2024 at 10:57am
|
This is a followup to a post on May 20 2015 from Kurto asking about a starter for the d grader he purchased. It appears the WD45 engine was replaced with the D15 2.9L diesel engine. The flywheels are not the same diameter and the and the starter gears are 10 for the original versus 9 for the replacement. Therefore 3 questions: Will the flywheel from the WD45 bolt to the D15 crank making the original starter work? Is it worth the trouble? The torque is muck less as the WD45 produces 288 foot pounds versus the D15's 127. Is there a better engine swap as the D15 needs to be pulled anyway? Thanks for the help
|
Replies:
Posted By: steve(ill)
Date Posted: 16 Jan 2024 at 2:11pm
|
there are BIG engines and SMALL engines... The D17 , WD45 used a 226 cubic inch engine.. THe WD and WC used a 201 engine with a very similar block.. Those will all interchange.. The SMALLER engine was a 125 cubic inch used in the B and C tractors.. THen upgraded to a 138 or 149 inch for the D10- 12- 14--- and then 15 tractors. Those are all interchangable, (among themselves) but SMALLER HOUSING than the LARGER 201- 226 motors, and not interchangable with them.
------------- Like them all, but love the "B"s. |
Posted By: DiyDave
Date Posted: 16 Jan 2024 at 4:29pm
|
D-17 motors should bolt right into the D grader... ------------- Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need! |
Posted By: newbe2
Date Posted: 16 Jan 2024 at 10:04pm
|
Thanks for replying. Will the D17D 262 diesel, with a frame extension, interchange as well? If so, which starter would I use? Which engine would be the most reliable? Any suggestions on a better way, I am looking forward to having something to play with in my spare time.
|
Posted By: steve(ill)
Date Posted: 16 Jan 2024 at 10:15pm
|
You would find a LOT MORE 226 gas engines from the D17 or WD45... LOTS of them made and LOTS available for low rebuild cost and direct fit.. ------------- Like them all, but love the "B"s. |
Posted By: Gary
Date Posted: 17 Jan 2024 at 7:57am
|
WC, WD,, and WD45 201 and 226 used the Model 'W' Block. D-10, D-12, D-14, D-15 138, 149, and 160 used the Model 'G' Block. Allis bot the Buda Engine Co. in 1953. G |
Posted By: ac fleet
Date Posted: 17 Jan 2024 at 10:13am
|
wd-45 and never look back! --- looks like that is what my 1950 D is going to get! ------------- http://machinebuildersnetwork.com/ |
Posted By: newbe2
Date Posted: 18 Jan 2024 at 11:18am
|
I am in Southern California where there is not a lot of AC salvage yards to poke around in, so I need a little help. I would like to replace the D15 2.9L 4cyl Diesel with one of the following D17 3.7L. gas, D17 4.3L diesel or the WD45 3.8L Buda Diesel. The shipping cost adds to the misery so I would like to do it right the first time. Extending the frame to accommodate the 6 does not appear to be a problem, I think I can deal with that. The only other choice I see is to pull the D15 engine and put the WD45 flywheel on it, if that even works. Of the three engines which would be the most useful in the D road grader? I live over a mile from the nearest maintained pave road and there is another 2 miles of road past me that needs to be maintained. My skip loader is wearing out, so I need to do something. Thanks for any help you can provide. |
Posted By: steve(ill)
Date Posted: 18 Jan 2024 at 12:42pm
|
Gary, i think what eveyone is telling you is the grader probably came with a motor very similar if not exactly the same as a D17 tractor.. Then apparently it was MODIFIED to make a D15 motor fit. It should not fit the bell housing, and the flywheel and starter would not fit so the D15 parts were used... It would appear the easiest and least expensive way to fix this would be to go back to the D17 gas engine with its flywheel and starter motor.. Should bolt right up to the ORIGINAL bell housing ... is there some type of adaptor plate that was added to get the D15 motor to fit ? THe diesel motor are less popular or at least less AVAILABLE , and additional modifications would need to be done... Assuming you have the ORIGINAL bell housing on the tractor, the D17 gas 226 should bolt right in... Gas motor should be readily available, cheaper, and easier to rebuild than the diesels. ------------- Like them all, but love the "B"s. |
Posted By: newbe2
Date Posted: 18 Jan 2024 at 1:42pm
|
Thanks Steve There is a 1/2 adapter plate, which may have moved the flywheel forward loosing contact with the starter, or I haven't found the right starter yet. The D17 gas is a good option, if I can find one in good shape without actually seeing it.
|
Posted By: ac fleet
Date Posted: 18 Jan 2024 at 5:38pm
|
figure on a rebuild job on whatever motor you buy! ------------- http://machinebuildersnetwork.com/ |
Posted By: steve(ill)
Date Posted: 18 Jan 2024 at 5:52pm
|
Gary... it is a ways off, but if you want a good deal from a trustworthy guy, you might contact Steve or Lon in Minnesota... Both have GOBS of parts and a few motors ... They could get you the engine, flywheel and starter you need.. to ACs post.. opening the motor and checking bearings, rebuild the oil pump, grind valves, install new rings and gaskets... is always a good way to Freshen up an old motor.. You dont need to go overboard with parts. https://www.allischalmers.com/forum/f-s-to-many-parts_topic199188.html" rel="nofollow - https://www.allischalmers.com/forum/f-s-to-many-parts_topic199188.html ------------- Like them all, but love the "B"s. |
Posted By: Les Kerf
Date Posted: 19 Jan 2024 at 8:53am
I doubt that the right starter exists for a Frankenstein setup like this, and if it does then it is just by blind luck rather than proper design. You would need to make careful measurements of the flywheel-to-starter relationship, and then start looking at drawings of various starters. You might get lucky! You may have better luck finding a complete WD or WD-45 that already runs
|
newbe2 wrote: