1952 WD oil bath air cleaner
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=194244
Printed Date: 08 May 2024 at 10:46am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 1952 WD oil bath air cleaner
Posted By: Mikey Joe
Subject: 1952 WD oil bath air cleaner
Date Posted: 25 Mar 2023 at 10:10am
| I have thoroughly cleaned the inside (including the mesh screen and the outer/inner air passages) of the oil bath air cleaner. Some how oil is being pulled into the carburater. I only filled the bowl to the fill line with 10W-30 engine oil. Why is this happening is happening? |
Replies:
Posted By: AC720Man
Date Posted: 25 Mar 2023 at 4:48pm
|
Use SAE 30 wt and make sure you are not over filling it. Stay below the line. The 10w-30 may be too light if you haven’t over filled it. ------------- 1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD |
Posted By: DMiller
Date Posted: 25 Mar 2023 at 5:14pm
| Straight 30 will not bubble thru as will the 10W30 |
Posted By: Mikez
Date Posted: 25 Mar 2023 at 5:43pm
| Welcome to the forum |
Posted By: steve(ill)
Date Posted: 25 Mar 2023 at 5:55pm
|
i have never had a problem using 10w 30... are you SURE the inside screen is clean ? Not just the part you can see... you need to SOAK the air cleaner in a bucket of diesel / gas/ solvent ... then drain and blow out with air... If you plug up 30% of the air path, the remaining area has to pull MORE AIR thru a smaller section and the extra velocity can carry more oil thru.
------------- Like them all, but love the "B"s. |
Posted By: wjohn
Date Posted: 25 Mar 2023 at 8:04pm
|
Any chance it has a WD-45 engine, or has been rebuilt with WD-45 components? Not sure if the slightly bigger displacement would cause it to suck oil in (experts on here probably know if this happens), but I think the WD air cleaner was smaller than the WD-45. Just a thought for something else to check. ------------- 1939 B, 1940 B, 1941 WC, 1951 WD, 1952 CA, 1956 WD-45 |
Posted By: jvin248
Date Posted: 25 Mar 2023 at 8:40pm
Probably not a bad idea, small restrictions in the air flow path could increase air velocity and vacuum.
|
wjohn wrote:Posted By: MACK
Date Posted: 25 Mar 2023 at 8:45pm
|
Take the wire mash out, soak it in gas then set the mash on fire. When it cools, unroll it and knock the dirt out. Next, cut top of housing off just below where it starts to taper down. Use a wire to clean dirt out between inside and outside wall. When clean bronze top back on. You won't believe how it ever ran before. You will think the mash is going to burn up, but it won't. May have to burn it the second time to get clean. MACK
|
Posted By: steve(ill)
Date Posted: 25 Mar 2023 at 8:51pm
|
https://www.allischalmers.com/forum/service-clean-oil-bath-air-cleaner_topic172101.html%20" rel="nofollow - https://www.allischalmers.com/forum/service-clean-oil-bath-air-cleaner_topic172101.html
------------- Like them all, but love the "B"s. |
Posted By: Mikey Joe
Date Posted: 26 Mar 2023 at 9:12am
| I dissembled the air cleaner and used degreaser on the interior mesh. I then soaked and "sloshed" the entire cleaner body in a 5 gallon bucket of hot water with Dawn. Did this several times over a couple of days. After that I sprayed degreaser in the air inlet between the outer shell and inner liner. Finally I used a compressed air wand to blow out the interior of the shell. Did a final soak/rinse with hot water and Dawn. This time the liquid was clear coming out of the air cleaner shell. |
Posted By: Mikey Joe
Date Posted: 26 Mar 2023 at 9:14am
| Engine straight WD except for manifold. It is from a D-17. |
Posted By: IBWD MIke
Date Posted: 26 Mar 2023 at 9:20am
I'm going to do this for the Narrow Front 45. Have an extra one in the parts vault, just get it ready then swap it out. I did the first half to the one in the wide front when I put the power steering on. Wasn't aware of there being a second half! It blew my mind how much 'stuff' came off the mesh when I burned it! I suppose once I get the NF done I could do the one that comes off and put it on the WF. Here I told myself I was going to try to slow down on the projects this year.
|
Posted By: steve(ill)
Date Posted: 26 Mar 2023 at 9:31am
|
Mikey, if you want to run a TEST, pull the rubber hose off to the carb and run the tractor for 30 minutes and see if it runs different.. or take the oil bowl off the air cleaner and run it that way... of course your not going to get any oil in the carb during this test, but you might see a difference in throttle response or power ?
------------- Like them all, but love the "B"s. |