wd45 3pt conversion swaybar
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=192415
Printed Date: 22 Aug 2025 at 6:21am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: wd45 3pt conversion swaybar
Posted By: TOOLMAKER4
Subject: wd45 3pt conversion swaybar
Date Posted: 16 Dec 2022 at 4:25pm
|
i have a wd 45 with a three point coversion. it has factory ps. wide front end with two sets of two way hyd. ports. the problem i am having is the sway of the lift arms when using some of the attachments. has anyone added sway bars to the 3pt converted wd's. i am looking to fabricate something to control the sway of the implement. |
Replies:
Posted By: exSW
Date Posted: 16 Dec 2022 at 4:37pm
Should look like this.
------------- Learning AC...slowly |
Posted By: TOOLMAKER4
Date Posted: 16 Dec 2022 at 4:52pm
| not sure what your picture is showing me or how it works |
Posted By: mdm1
Date Posted: 16 Dec 2022 at 6:03pm
|
That goes between the lift arms on one style of conversion. I took mine off and put cross chains on instead because it interfered with a pto shaft. Do a search for allis 3pt conversions. Had trouble uploading a pic. ------------- Everything is impossible until someone does it! WD45-trip loader 1947 c w/woods belly mower, 1939 B, #3 sickle mower 1944 B, 2 1948 G's. Misc other equipment that my wife calls JUNK! |
Posted By: jvin248
Date Posted: 16 Dec 2022 at 6:33pm
|
. Pull up pictures of Ferguson 3 point tractors. You'll see how sway chains and bars are attached for different conditions. Then adapt to your AC.   |
Posted By: exSW
Date Posted: 16 Dec 2022 at 6:52pm
I'll get better pictures. The part in my hand has a long bolt(14") that runs transversely through it mounting it between the two lift brackets bolted to the bottom of the rear end housing. Does an excellentjob of limiting sway a keeps the three point apparatus from contacting the ground. I've been moving 800# round bales with standard three point bale spear with no issues.
------------- Learning AC...slowly |
TOOLMAKER4 wrote:Posted By: mdm1
Date Posted: 17 Dec 2022 at 6:37am
 This is the hitch that he is showing the pic of. I have the same style and I'm sure it works fine with a bale spear. My pto shaft for my brush mower would get in the way so I just put cross chains on it. What do you have for a conversion on your tractor?------------- Everything is impossible until someone does it! WD45-trip loader 1947 c w/woods belly mower, 1939 B, #3 sickle mower 1944 B, 2 1948 G's. Misc other equipment that my wife calls JUNK! |
Posted By: TOOLMAKER4
Date Posted: 17 Dec 2022 at 12:16pm
|
i have the 3pt conversion that has a 3" square tube with flat brackets that bolt to the draw bar bracket. i am thinking to add another short piece of 3" square and another flat piece with a hole to put another threaded pin in to keep the swing point the same as the lift arms, then drilling a hole for another threaded pin in the lift arm just out past the scew jacks that go up to the snap coupler on the ac factory lift arms. then making a center link style arm to go between the two treaded pins. |
Posted By: TOOLMAKER4
Date Posted: 17 Dec 2022 at 12:23pm
this is the three point conversion i have
|
Posted By: TOOLMAKER4
Date Posted: 17 Dec 2022 at 12:26pm
|
Posted By: TOOLMAKER4
Date Posted: 17 Dec 2022 at 12:29pm
|
sorry first try at sending pic was a epic failure. |
Posted By: mdm1
Date Posted: 17 Dec 2022 at 12:40pm
|
That horizontal piece that sits on the drawbar should take care of your problem. ------------- Everything is impossible until someone does it! WD45-trip loader 1947 c w/woods belly mower, 1939 B, #3 sickle mower 1944 B, 2 1948 G's. Misc other equipment that my wife calls JUNK! |
Posted By: Brian G. NY
Date Posted: 19 Dec 2022 at 4:02pm
That little piece with the chains is not a real anti sway setup. It more or less keeps the arms from flopping all over when no 3PH implement is attached. The A-C 3PH adaptor uses this setup. I have a homemade 3PH adaptor on my D-17 made by the prior owner. It leaves a little to be desired but I really like the anti sway system. I have a Bush Hog that I use a lot on side hills and having the weight of it flopping back and forth could be dangerous. These adjustable anti sway bars are available from TSC and they can be adjusted to practically eliminate all sway. Of course, it requires a little fabrication for mounting the front pins but uses the original 3PH pins on the outer ends
 . |