D14 Final drive spacer
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=180732
Printed Date: 24 Nov 2024 at 9:45pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: D14 Final drive spacer
Posted By: bozrae
Subject: D14 Final drive spacer
Date Posted: 24 May 2021 at 5:41am
|
Bought a D14 last fall and didn't notice until recently that it had spacers on the final drives. I looked this up in the online Agco Parts book and it does show them. It says they are for 63" to 97" wheel tread. I've never seen these, does anyone know what implement they would be used for and how common are they?  ------------- D15D, D17G, 170G, 175D, and two 5050FWA |
Replies:
Posted By: Fred in Pa
Date Posted: 24 May 2021 at 12:16pm
Here is a set I will be installing on a D-15 series 2 diesel along with a single front wheel for a forum member that I am rebuilding tractor for. ,he can jump in and fill u in on what he's doing it for.  ------------- He who dies with the most toys is, nonetheless ,still dead. If all else fails ,Read all that is PRINTED. |
Posted By: steve(ill)
Date Posted: 24 May 2021 at 12:36pm
|
Fred, is there an extension for the top shaft, or is it one complete DIFFERENT part from the standard D15 ? ------------- Like them all, but love the "B"s. |
Posted By: Fred in Pa
Date Posted: 24 May 2021 at 1:52pm
|
Top shaft Is longer ------------- He who dies with the most toys is, nonetheless ,still dead. If all else fails ,Read all that is PRINTED. |
Posted By: ACinSC
Date Posted: 24 May 2021 at 2:17pm
| I was also wondering about the pinion shaft . Thanks |
Posted By: bozrae
Date Posted: 25 May 2021 at 5:53am
|
Were these used if you wanted a mounted corn picker? ------------- D15D, D17G, 170G, 175D, and two 5050FWA |
Posted By: Richardmo
Date Posted: 25 May 2021 at 10:30am
|
They were used on the high crops D 14 and 15. How wide are the spacers? |
Posted By: bozrae
Date Posted: 25 May 2021 at 12:29pm
|
The spacers are 4-5/16" wide. The reason I thought they might be for a mounted corn picker is because is has what looks to be a factor screen enclosure on the air intake. ------------- D15D, D17G, 170G, 175D, and two 5050FWA |
Posted By: Fred in Pa
Date Posted: 25 May 2021 at 2:48pm
|
6 1/2 on the axle's I am working on ------------- He who dies with the most toys is, nonetheless ,still dead. If all else fails ,Read all that is PRINTED. |
Posted By: mruhlig77
Date Posted: 25 May 2021 at 4:14pm
|
In your AGCO book..do the spacers imply a high-crop or a single front end????I would bet on the corn picker or vegetables....Mark |
Posted By: Richardmo
Date Posted: 25 May 2021 at 7:43pm
|
The high crops have the wider one. Also check the parts book calls out for a different axle for the picker so maybe that is what that is for. |
Posted By: mruhlig77
Date Posted: 26 May 2021 at 3:34pm
| Found my own D-15 book ....appears there were also 3 widths of wide front ends....did not list applications of the wider rear....Mark |
Posted By: bozrae
Date Posted: 27 May 2021 at 7:14am
Here is some info from the online book. They have different part numbers for pinion shafts but only one part number for a RH and LH side spacer. ------------- D15D, D17G, 170G, 175D, and two 5050FWA |