WC Project conundrum!
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=179854
Printed Date: 01 Apr 2026 at 11:18pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: WC Project conundrum!
Posted By: jollymon68
Subject: WC Project conundrum!
Date Posted: 14 Apr 2021 at 8:53pm
So i just got a WC SN 143796S, it is a steel rear end and Gas/Kerosene tractor. I have not started it but the engine is free. For some reason the starter switch is on the opposite side of the missing starter push rod. The starter switch has no mount for a starter rod lever either. Second there is another pull rod on the steering column that goes all the way to the magneto but is not connected anywhere. Any ideas as to what gives with these differences in this WC? Pics attached.  
|
Replies:
Posted By: JC-WI
Date Posted: 14 Apr 2021 at 9:18pm
|
Got a rod going to the choke? ------------- He who says there is no evil has already deceived himself The truth is the truth, sugar coated or not. Trawler II says, "Remember that." |
Posted By: jollymon68
Date Posted: 14 Apr 2021 at 9:37pm
| Yes the rod closest to the steering wheel goes to the choke. The the one furthest is not connected. Think it is the magneto shut off for the engine when running, but not connected to anything. |
Posted By: mdm1
Date Posted: 15 Apr 2021 at 8:35am
|
https://www.allischalmers.com/forum/electric-start-on-wc_topic26985.html " rel="nofollow - https://www.allischalmers.com/forum/electric-start-on-wc_topic26985.html ; Check Bill Long's response at the end of the page. May explain the starter switch? ------------- Everything is impossible until someone does it! WD45-trip loader 1947 c w/woods belly mower, 1939 B, #3 sickle mower 1944 B, 2 1948 G's. Misc other equipment that my wife calls JUNK! |
Posted By: steve(ill)
Date Posted: 15 Apr 2021 at 8:45am
|
The starter switch has no mount for a starter rod lever either. YEA.. if you are use to hand cranking the motor from the front, walking to the side and PUSHING THE BUTTON would have been a real upgrade ! ------------- Like them all, but love the "B"s. |
Posted By: jollymon68
Date Posted: 15 Apr 2021 at 12:29pm
| Thanks guys for the starter info... I’m going to install a push rod and flip the starter. Now I just got figure out where the other pull rod attaches. |
Posted By: Steve in NJ
Date Posted: 15 Apr 2021 at 1:57pm
|
The Magneto that should be on that particular WC with the rod kill should be a FMJ4B3A. The "A" indicates the grounding lever is on the engine side of the Mag. There is a special lever that mounts to the side of the Mag that the rod goes into to ground the Mag and shut down the engine. I have them in stock & on the website in the 2 piece Mag section so you can see what it looks like. Looking at your picture, the Magneto has been changed and a regular 4B3 Mag has replaced the 4B3A original. That's the reason the rod is there for the ride....... Steve@B&B bb-customcircuits.com ------------- 39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife |
Posted By: jollymon68
Date Posted: 15 Apr 2021 at 2:30pm
| Thanks Steve! That is exactly the info I needed and you are right about the mag being changed out. Checked the numbers and you are spot on as usual. |