D15 II Power Steering
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=178015
Printed Date: 10 Jan 2025 at 5:02pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: D15 II Power Steering
Posted By: Charlie175
Subject: D15 II Power Steering
Date Posted: 01 Feb 2021 at 9:55am
|
Are the power steering hoses still available? I looked on agcoparts but couldn't find them. Was looking at replacing these partial rubber hoses while we have it apart. 52 years figure they would be cracking up by now... D15 series 2 (Late model)
------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Replies:
Posted By: Alvin M
Date Posted: 01 Feb 2021 at 10:09am
| Page # 286 |
Posted By: Gary Burnett
Date Posted: 01 Feb 2021 at 10:15am
|
Watch the AGCO hoses I bought a PS hose from AGCO for my Oliver 1365 fittings were not right,one of the mechanics made me one up that worked perfect, plus I ended up about $50 to the good. |
Posted By: Charlie175
Date Posted: 01 Feb 2021 at 11:39am
Those are similar but don't match entirely to what I have. ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Alvin M wrote:Posted By: Joe(TX)
Date Posted: 01 Feb 2021 at 11:43am
|
There is only one hose on the PS. It is the return hose. The rest are tubes from the factory. ------------- 1970 190XT, 1973 200, 1962 D-19 Diesel, 1979 7010, 1957 WD45, 1950 WD, 1961 D17, Speed Patrol, D14, All crop 66 big bin, 180 diesel, 1970 170 diesel, FP80 forklift. Gleaner A |
Posted By: Charlie175
Date Posted: 01 Feb 2021 at 11:44am
These are what I am looking for  ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Posted By: PaulB
Date Posted: 01 Feb 2021 at 12:12pm
|
Charlie: Send them to Inline tube They can match them exactly as the originals, with the hose parts and the tube parts with all the correct bends. ------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
Posted By: Charlie175
Date Posted: 01 Feb 2021 at 1:23pm
|
Thanks Paul! ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Posted By: tomstractorsandtoys
Date Posted: 01 Feb 2021 at 5:37pm
|
When you get what you need post back with the price as my series II should have a set as well. Tom |
Posted By: DSeries4
Date Posted: 01 Feb 2021 at 8:42pm
|
Here is what I have done. I took all the lines to my local hydraulic
shop. They made new flexible sections the same size and provided me
with compression fittings. I cut out the old flexible pieces, put the
new ones in place and tighten down the fittings. Pretty cheap too. How do these look?  
------------- '49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080 |
Posted By: Charlie175
Date Posted: 02 Feb 2021 at 6:51am
|
That works! Might have to try that ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Posted By: Fred in Pa
Date Posted: 02 Feb 2021 at 8:00am
|
Been using those compression fitting for years u just need a good round steel line to install them . ------------- He who dies with the most toys is, nonetheless ,still dead. If all else fails ,Read all that is PRINTED. |
Posted By: Alex09(WI)
Date Posted: 02 Feb 2021 at 9:30am
|
I have the D15 II lines ready-made and on the shelf if you want to go that route.  ------------- www.awtractor.com A&W TRACTOR 920-598-1287 KEEPING ALLIS-CHALMERS IN THE FIELDS THROUGH THE 21ST CENTURY |